Independent Australian Cost Guides
Updated November 2026
← All commercial trades

How much do commercial garage doors cost in Perth?

Commercial garage doors run $2,850–$25,000
installed, depending on door type, size and automation
Perth's $2,850–$25,000 spans an installed industrial roller shutter through to a rapid-roll door, supply and install, priced per door. A Canning Vale cold store looking at insulated PU-core sectional panels faces $280–$380 per m² of door, supply only, and a motorised roller door near 3m x 3m is $3,200–$5,500 installed.
+4.5% Commercial garage door prices are up around 4.5% over the past year, re-verified against 90+ sources in November 2026. Year on year
Typical Industrial Roller Shutter
$4,500
per commercial roller door, installed
Roller Shutter
$2,850–$12,000
Insulated
$280–$380/m²
Sectional
$3,450–$19,800
Roller $2,850Sectional $9,700High-speed $25,000

A commercial garage door in Perth costs $2,850–$25,000 installed, rising from industrial roller shutters through sectional overhead doors to high-speed rapid-roll doors. Opening size and the motor matter most within each type; a motorised roller door for a 4m x 4m opening is $4,600–$7,500 installed.

Perth's industrial land is widely spread, from Malaga and Wangara in the north to Kewdale and Welshpool near the airport and Bibra Lake, Jandakot and Henderson in the south. Big shutters on logistics and mining-supply sheds use heavier operators, which explains the wide motor replacement range of $750–$3,500 per door.

Plan on an annual service at $150–$350 a year for each door. Roller door and shutter prices include GST; sectional, insulated-panel and rapid-roll prices are ex GST, as marked in the table.

Comparing cities, or after the Australia-wide picture? See the national guide: How much do commercial garage doors cost in Australia?

Quick answerA commercial garage door costs $2,850–$25,000 installed depending on type — roller shutters at the low end, high-speed rapid-roll doors at the top. Get free commercial quotes →

Commercial Garage Door Prices in Perth 2026: Cost Table and Price List

ServiceLowTypicalHigh
Industrial roller shutter (per door, installed)$2,850installed$4,500$12,000
Insulated commercial door (PU-core sectional, supply only, per sqm of door, ex GST)$280/sqm$330$380
Commercial sectional overhead door (installed, ex GST)$3,450installed$9,700$19,800
High-speed / rapid-roll door (supply + install, ex GST)$11,000supply+install$15,000$25,000
Roller door ~3m x 3m, manual (installed)$2,000installed$2,650$3,600
Roller door ~3m x 3m, motorised (installed)$3,200installed$4,200$5,500
Roller door ~4m x 4m, motorised (installed)$4,600installed$5,700$7,500
Roller door ~5m x 5m, motorised (installed)$6,000installed$7,300$10,000
Door motor / operator replacement$750per door$1,950$3,500
Annual door service (per door)$150per year$250$350
Step 1 of 2

What do you need a callback about?

One tap — we'll show you the going rate, then take your number.

You're in.

A local installer will be in touch about your job. No spam, no call centre.

Scoping a commercial garage door? Get a quote from an Australian commercial door installer — free, no obligation.

Get commercial quotes →
Prices verified November 2026 · Cross-referenced against Australian commercial garage door suppliers · See methodology

Prices include GST unless the row says ex GST. Perth-wide, November 2026. Large or custom openings vary.

Commercial garage door prices in Perth by door type

Garage roller doors Perth prices start with the plain steel curtain and climb through sectional, insulated and rapid-roll doors, and each type is quoted on its own basis. Here is what the main door types cost across the metro area, from the Neerabup estates in the north to Rockingham in the south.

Use the form on this page to get quotes from commercial garage door installers in Perth.

Commercial vs residential garage doors — why commercial costs more

A Perth commercial door does more work in harsher conditions than a house door. A mining-services workshop in Kwinana or Welshpool may open its big bay through two shifts, so the curtain is heavier gauge, the springs larger and the operator built for sustained duty, often on three-phase power. Summer heat bakes motors and seals, and dust works into guides. Larger spans, interlocks and installation around a working yard all lift the price well past a household door.

Commercial garage door sizes and how size drives price

Size changes a Perth roller door price in steady steps. Around 3m x 3m a manual door costs $2,000–$3,600 installed and a motorised one $3,200–$5,500, enough for a ute or van bay at a Balcatta trade unit. About 4m x 4m, for light trucks, costs $4,600–$7,500 motorised. Around 5m x 5m, taking a rigid truck at a Bassendean depot, the price is $6,000–$10,000. Openings larger again are quoted as industrial shutters.

What Actually Moves the Commercial Garage Door Cost in Perth

How to Keep the Commercial Garage Door Cost Sane in Perth

1
Have the guides and barrel inspected before agreeing to a full replacement; on a sound frame, a new curtain may be all a dented door needs.
2
Ask whether the operator behind a west-facing door is rated for the afternoon heat that builds up inside, since a motor that runs hot wears out sooner.
3
Book servicing at $150–$350 a year per door, before summer, so dry guides and perished seals are dealt with early.
4
Keep the yard swept in front of busy bays, since grit carried into the guides and bottom seal wears them faster.
5
Leave a rarely used storeroom door manual; a manual door around 3m x 3m at $2,000–$3,600 installed avoids paying for a motor that would barely run.

Commercial garage door cost by door type

Quick answerPerth budgets by door type: an industrial roller shutter costs $2,850–$12,000 installed, a commercial sectional door $3,450–$19,800 installed ex GST, and a rapid-roll door $11,000–$25,000 supplied and installed ex GST.

Shutters are the low-cost, hard-wearing answer for yards and sheds, and they are common on bays across the eastern and southern industrial suburbs. Sectionals cost more for rigid panels, tracks and springs, and repay it with a better seal against heat and dust and a finished face for showrooms. Rapid-roll doors cost the most and suit only openings that cycle all day, such as chilled food handling. Remember that sectional, insulated-door and rapid-roll figures are ex GST, while shutter figures include it.

Our Methodology

Commercial pricing on this page is compiled from Australian commercial and industrial garage-door suppliers and installers, published supplier price guides and product ranges as of November 2026. We cross-reference ranges from multiple sources; no contractor can influence a published figure. All prices are estimates, GST-inclusive unless a row says ex GST, and will vary with your specific opening, door spec and site. Always get multiple written quotes. Last reviewed November 2026. Read our full methodology →

Commercial garage door prices, product by product

Industrial roller shutters cost $2,850–$12,000 installed, typically $4,500. A rolled steel curtain coils onto a barrel and runs in guides, driven by a chain hoist or motor. Wide yards and mining-supply sheds push a door up the band through heavier curtains, wind locks and three-phase operators, while a single-truck bay with a modest drive stays low.

Commercial sectional overhead doors run $3,450–$19,800 installed, ex GST, typically $9,700. Insulated panels hinge and roll up tracks, so the layout depends on headroom: a low-headroom kit under a tight roof, high-lift or vertical-lift tracks in a tall shed. Full-view aluminium for a showroom, windows, a pass door and a heavy operator lift the price, and light colours help panels stay cooler in summer sun.

Insulated PU-core sectional doors cost $280–$380 per m² of door, ex GST and supply only, with $330 per m² typical. A dock door 6m wide and 5m high is 30 m², about $9,900 ex GST to supply at the typical rate, and installation is quoted on top. Thicker cores and better seals belong at the upper end.

Rapid-roll doors cost $11,000–$25,000 supplied and installed, ex GST. The price covers a light fabric curtain that cycles in seconds, a high-speed drive and controller, and sensors that open it as a forklift approaches. Internal doors in a chiller sit lower in the band, while external doors facing the weather need a curtain built to resist wind pressure both ways.

Commercial garage doors — go deeper

Which door for which job?

A transport depot, mining-supply shed or fabrication workshop from Hazelmere to Kwinana: an industrial roller shutter with a three-phase operator and wind locks, sized for the largest vehicle using it.

A showroom or trade counter in Osborne Park or along a main road: a sectional door, glazed if customers see it, because it seals out dust and heat and looks finished.

A cold store or food business near the Canning Vale produce market: rapid-roll doors on chilled internal openings and an insulated sectional on the external dock to hold temperature through summer.

Red flags when comparing commercial door installers

Commercial garage door cost in Perth: roller, sectional and motor prices

Commercial garage doors in Perth cost $2,000–$3,600 installed for a manual roller door around 3m x 3m and $3,200–$5,500 installed once motorised. Larger motorised roller doors cost $4,600–$7,500 installed at around 4m x 4m and $6,000–$10,000 installed at around 5m x 5m, typically $7,300. Commercial sectional overhead doors cost $3,450–$19,800 installed ex GST, and high-speed rapid-roll doors $11,000–$25,000 supplied and installed ex GST.

Perth's industrial areas in Welshpool, Kewdale, Malaga, Osborne Park, Canning Vale and Henderson are home to many warehouses and workshops with large roller doors, and long hot summers with strong easterly winds are hard on curtains and motors. Industrial roller shutters cost $2,850–$12,000 installed. Motor replacement here spans $750–$3,500 per door with $1,950 typical, because heavy industrial operators on large shutters cost well above lighter units. Coastal sites in Fremantle and Cottesloe also contend with salt air.

An annual service costs $150–$350 a year per door and should cover springs, guides, the curtain, the motor's limits and the safety reversing function. A good Perth commercial door quote should confirm the door size and type, the curtain or panel gauge, the motor model and its duty rating, safety beams and manual override, heat and dust protection for the operator, removal of the old door, and whether prices include GST.

What a Compliant Commercial Garage Door Quote Includes — Cost in Perth

Perth commercial garage door quotes should name the door, the opening and the price basis before anything else. Salt air at Fremantle and Cottesloe, summer heat on an operator and ex GST versus inclusive figures all change the total, so ask for each in writing.

Residential garage doors prices vs commercial garage door costs in Perth

Residential garage doors prices are what most people look up first, but a commercial door in Perth is a different purchase: wider openings, heavier curtains, three-phase operators and a service history the landlord asks for. The jobs below show what commercial work costs across the city.

Use the form on this page to get quotes from commercial garage door installers in Perth.

Frequently Asked Questions — Commercial Garage Door Cost in Perth

What do installers charge for a roller shutter in Perth?
Our Perth prices for an industrial roller shutter (per door, installed) start at $2,850 and reach $12,000, with $4,500 typical.
How much is a panel-lift commercial door in Perth?
Going by our Perth table, expect $3,450–$19,800 for a commercial sectional overhead door (installed); the typical price is $9,700.
What are commercial garage door prices in Perth?
In our Perth table the figures are $3,200–$5,500 installed for a motorised roller door about 3 m x 3 m (typically $4,200), $3,450–$19,800 installed for a commercial sectional overhead door (typically $9,700) and $2,850–$12,000 installed for an industrial roller shutter (typically $4,500).
What does replacing a commercial door motor cost in Perth?
Replacing the motor on a commercial door in Perth costs $750–$3,500 per door, typically $1,950 per door. A light operator on a small roller door sits near the bottom, while a heavy three-phase unit driving a large shutter in Welshpool or Kewdale sits near the top. Ask whether the price covers new remotes, safety beams, travel limit setting and removal of the old motor.
Are Perth commercial door prices quoted with or without GST?
In Perth, sectional overhead doors at $3,450–$19,800 installed, insulated panels at $280–$380 per square metre of door supplied only, and rapid-roll doors at $11,000–$25,000 supply and install are all ex GST figures. Add GST before comparing them with any quote shown inc GST. For roller doors, shutters, motors and servicing, ask each installer to state the GST basis on the quote.
What does a commercial door service cost in Perth?
A commercial door service in Perth costs $150–$350 per year per door, typically $250 per year. The technician should check spring tension, the curtain or panels, guides, bearings, motor limits and the safety reversing function. Summer heat dries out lubricants and perishes seals, and coastal sites at Fremantle or Henderson collect salt in the guides, so exposed doors benefit from regular attention.
What does replacing an old commercial garage door cost in Perth?
Replacing a tired commercial door in Perth means $3,200–$5,500 installed for a motorised roller door around 3m by 3m, $2,850–$12,000 installed for an industrial roller shutter, or $3,450–$19,800 installed, ex GST, for a sectional overhead door. Ask for removal and disposal of the old curtain or panels, a check of the lintel and side fixings, and reuse or replacement of the existing operator to be spelt out. Fremantle and Cottesloe doors in salty air often need new guides as well, which the installer should price up front.
What does a high-speed rapid-roll door cost in Perth?
A high-speed rapid-roll door in Perth is $11,000–$25,000 supply and install, ex GST, with $15,000 typical. They go on busy internal openings at food and beverage plants, cold stores and distribution sheds in Canning Vale, Malaga and Bibra Lake, where the fast fabric curtain holds refrigerated air and keeps summer heat and dust outside. The quote should name opening size, curtain speed, activation method and the frame finish. Small internal doors sit low; wide external openings with wind-rated curtains for an exposed site reach the upper end.
How much is a 5m x 5m motorised roller door in Perth?
Perth businesses pay $6,000–$10,000 installed for a motorised roller door around 5m by 5m, typically $7,300. That opening suits truck depots and machinery sheds in Welshpool, Kewdale and Wangara, as well as boat storage along the coast. The figure assumes a sound existing opening; a new steel lintel, a crane for the drum or a three-phase power run add separate lines. Dropping to around 4m by 4m gives $4,600–$7,500 installed, which covers most van and light truck access.

Advertise with us

Reach Australian businesses researching commercial service costs. Fill in your details and we'll be in touch within 1 business day.

Thanks! We'll be in touch

Expect a reply within 1 business day.

Got a question about costs?
Chat with Sam
Sam the Platypus
Online now
Powered by What's The Damage