Independent Australian Cost Guides
Updated November 2026
← All commercial trades

How much do commercial garage doors cost in Brisbane?

Commercial garage doors run $2,900–$25,500
installed, depending on door type, size and automation
Brisbane's range is a per-door figure: $2,900 is the low end for an installed industrial roller shutter and $25,500 the high end for a rapid-roll door, supply and install. For a Geebung warehouse, a motorised roller door of about 4m x 4m is $4,700–$7,650 installed, and a replacement motor or operator later costs $765–$2,550 per door.
+5.2% Commercial garage door prices are up around 5.2% over the past year, re-verified against 90+ sources in November 2026. Year on year
Typical Industrial Roller Shutter
$4,600
per commercial roller door, installed
Roller Shutter
$2,900–$12,250
Insulated
$280–$380/m²
Sectional
$3,500–$20,200
Roller $2,900Sectional $9,900High-speed $25,500

Commercial garage doors in Brisbane cost $2,900–$25,500 installed, with industrial roller shutters at the lower end and high-speed rapid-roll doors at the upper end. The door type sets the starting point, and from there the opening size, the motor and options such as windows, pass doors or insulation decide the final figure.

Much of the city's commercial door work sits in the industrial suburbs near the airport and port, such as Eagle Farm, Pinkenba, Murarrie and Hemmant, and in the southern estates at Rocklea, Archerfield and Acacia Ridge. Summer storms bring strong gusts, so ask about wind locks and heavier guides on wide openings; a motorised roller door for a 5m x 5m opening runs $6,100–$10,200 installed.

Upkeep means servicing each door yearly, at $155–$355 a year, and eventually a new motor or operator, priced $765–$2,550 per door. GST is included in roller door and shutter prices, while sectional, insulated-panel and rapid-roll prices are shown ex GST.

Comparing cities, or after the Australia-wide picture? See the national guide: How much do commercial garage doors cost in Australia?

Quick answerA commercial garage door costs $2,900–$25,500 installed depending on type — roller shutters at the low end, high-speed rapid-roll doors at the top. Get free commercial quotes →

Commercial Garage Door Prices in Brisbane 2026: Cost Table and Price List

ServiceLowTypicalHigh
Industrial roller shutter (per door, installed)$2,900installed$4,600$12,250
Insulated commercial door (PU-core sectional, supply only, per sqm of door, ex GST)$280/sqm$330$380
Commercial sectional overhead door (installed, ex GST)$3,500installed$9,900$20,200
High-speed / rapid-roll door (supply + install, ex GST)$11,200supply+install$15,300$25,500
Roller door ~3m x 3m, manual (installed)$2,050installed$2,700$3,675
Roller door ~3m x 3m, motorised (installed)$3,275installed$4,275$5,600
Roller door ~4m x 4m, motorised (installed)$4,700installed$5,800$7,650
Roller door ~5m x 5m, motorised (installed)$6,100installed$7,450$10,200
Door motor / operator replacement$765per door$1,275$2,550
Annual door service (per door)$155per year$255$355
Step 1 of 2

What do you need a callback about?

One tap — we'll show you the going rate, then take your number.

You're in.

A local installer will be in touch about your job. No spam, no call centre.

Scoping a commercial garage door? Get a quote from an Australian commercial door installer — free, no obligation.

Get commercial quotes →
Prices verified November 2026 · Cross-referenced against Australian commercial garage door suppliers · See methodology

Prices include GST unless the row says ex GST. Brisbane-wide, November 2026. Large or custom openings vary.

Commercial roller shutters and other commercial garage door prices in Brisbane

Commercial roller shutters in Brisbane are the workhorse door on the city's industrial estates. The figures below are per door and cover the main types fitted on Brisbane sites, from Eagle Farm freight sheds to the trade units of Acacia Ridge and Brendale.

Use the form on this page to get quotes from commercial garage door companies in Brisbane.

Commercial vs residential garage doors — why commercial costs more

On a Brisbane industrial estate a door may cycle dozens of times a shift, take summer storm gusts across a wide opening, and need to keep a cool room cold through humid months. Commercial doors are built for that: heavier curtains and panels, stronger springs, guides that can take wind locks, and operators rated for sustained duty on single- or three-phase power. Add controls mounted above flood height on low-lying sites, and installation timed around trading, and the price leaves a house door well behind.

Commercial garage door sizes and how size drives price

Brisbane roller doors are quoted on the clear opening, and the steps are easy to read. Near 3m x 3m a manual door costs $2,050–$3,675 installed, rising to $3,275–$5,600 motorised, which suits a van bay at a Northgate or Virginia trade unit. Around 4m x 4m, a motorised door is $4,700–$7,650. Near 5m x 5m, big enough for container trucks around Lytton, it costs $6,100–$10,200. Past that size, expect an industrial shutter quote.

What Actually Moves the Commercial Garage Door Cost in Brisbane

How to Keep the Commercial Garage Door Cost Sane in Brisbane

1
Tell installers how many times a day each door runs, so the operator is sized for the real workload rather than an assumed worst case.
2
Keep a sound shutter and swap only the drive; a replacement operator costs $765–$2,550 per door.
3
Pay for an annual service at $155–$355 a year, timed before storm season, so guides, springs and wind locks are checked.
4
Pick a light curtain or panel colour for a door that faces the afternoon sun, which helps keep the shed behind it cooler.
5
Use a manual roller door on a bin store or rarely used storeroom and keep motors for the bays that work all day.

Commercial garage door cost by door type

Quick answerFor Brisbane, budget $2,900–$12,250 installed for an industrial roller shutter, $3,500–$20,200 ex GST for a commercial sectional overhead door, and $11,200–$25,500 ex GST for a rapid-roll door supplied and installed.

Start with what the opening does. A shutter is the low-cost, secure choice for freight bays and sheds, and it is found across the industrial estates around the port and the southern corridor. A sectional costs more for its panels, tracks and springs but seals and insulates better, which pays back in air-conditioned showrooms and workshops. A rapid-roll door costs the most of the three and makes sense only on an opening that cycles all day, such as a cool-room entry. Sectional and rapid-roll figures here exclude GST.

Our Methodology

Commercial pricing on this page is compiled from Australian commercial and industrial garage-door suppliers and installers, published supplier price guides and product ranges as of November 2026. We cross-reference ranges from multiple sources; no contractor can influence a published figure. All prices are estimates, GST-inclusive unless a row says ex GST, and will vary with your specific opening, door spec and site. Always get multiple written quotes. Last reviewed November 2026. Read our full methodology →

Commercial garage door prices, product by product

Industrial roller shutters cost $2,900–$12,250 per door installed, with $4,600 the typical figure. The curtain is roll-formed steel coiled over a barrel, with guides each side and an operator at one end. Width and curtain gauge set most of the price; wind locks, a three-phase drive and a powder-coated finish for salty air near the bay take a door higher.

Commercial sectional overhead doors cost $3,500–$20,200 installed, ex GST, typically $9,900. Insulated steel panels hinge together and run up tracks to sit under the roof. Windows, a pass door, full-view aluminium sections for a showroom and a heavy-duty operator each add to a door's price, and high-lift tracks suit tall warehouses with racking.

An insulated PU-core sectional door is $280–$380 per m² of door, supply only and ex GST, with $330 per m² typical. A door 4m wide and 4.5m high is 18 m², so about $5,940 ex GST to supply at the typical rate, with installation quoted on top. Thickness and the seal package decide where in the band a door falls.

Rapid-roll doors cost $11,200–$25,500 supplied and installed, ex GST. A flexible PVC or fabric curtain runs fast in side frames, triggered by radar, floor loops or pull cords, and many reset automatically after a forklift strike. Internal cool-room doors sit low in that band; exterior doors that face storm gusts need wind-resistant curtains and sit higher.

Commercial garage doors — go deeper

Which door for which job?

Freight sheds, container yards and trade warehouses around the port or the Wacol estates: an industrial roller shutter with wind locks and a duty-rated operator.

Air-conditioned showrooms, gyms and service workshops facing a main road: an insulated sectional, glazed on the street side, to keep heat out and present well to customers.

Food producers, cool rooms and market tenants at Rocklea: a rapid-roll door on busy internal openings and an insulated sectional on the dock, with motors and controls mounted high where the site has flooded before.

Red flags when comparing commercial door installers

Roller door sizes and prices in Brisbane

In Brisbane the clear opening sets the roller door row. For a small bay in a Geebung or Eagle Farm unit, a 3m x 3m door runs $2,050–$3,675 installed when it is lifted by hand and $3,275–$5,600 installed once a motor is fitted. Open it up to about 4m x 4m for small trucks and the motorised price is $4,700–$7,650 installed; about 5m x 5m, for a rigid truck at a Rocklea or Acacia Ridge yard, sits at $6,100–$10,200 installed.

Summer storms are the local variable. A wide curtain facing an open yard is often quoted with wind locks and heavier guides, which pulls the price toward the upper figure of its row, while a sheltered internal opening can sit near the lower figure. Bays that take forklift traffic all shift are usually priced as an industrial roller shutter at $2,900–$12,250 installed, typically $4,600, with width and curtain gauge deciding where a door lands.

Upkeep adds up across a complex of trade units. A landlord or body corporate with six roller doors on one Brisbane block would set aside $930–$2,130 a year for servicing at $155–$355 per door, and an operator that fails is replaced at $765–$2,550 per door.

Commercial garage door cost in Brisbane: roller doors by size, shutters, sectionals and rapid-roll

Commercial garage doors in Brisbane are priced per door, installed, and the door type sets the band before the size does. An industrial roller shutter costs $2,900–$12,250 per door. A commercial sectional overhead door, the insulated panel door used on showrooms and workshops, runs $3,500–$20,200 installed ex GST, and a high-speed or rapid-roll door for a loading dock or food premises $11,200–$25,500 supplied and installed ex GST.

For a standard commercial roller door, roller door size and the motor decide the price. A door of around 3m x 3m is $2,050–$3,675 installed as a manual door and $3,275–$5,600 motorised. At around 4m x 4m a motorised roller door is $4,700–$7,650, and at around 5m x 5m $6,100–$10,200. An insulated PU-core sectional, supplied only, is priced by the square metre of door at $280–$380 ex GST.

After the install, a Brisbane business pays two recurring lines: a door motor or operator replacement at $765–$2,550 per door when the original wears out, and an annual door service at $155–$355 per door. A commercial garage door quote should state the door type, the opening size, whether the motor is included and whether the price is ex or inc GST, since sectional and rapid-roll doors are commonly quoted ex GST and roller doors are not.

What a Compliant Commercial Garage Door Quote Includes — Cost in Brisbane

Before comparing Brisbane commercial garage door quotes, make sure each one describes the same door on the same basis. The table above mixes installed figures with ex GST supply figures, and a quote that blurs that line cannot be read against one that does not.

Frequently Asked Questions — Commercial Garage Door Cost in Brisbane

What does a commercial roller shutter cost in Brisbane?
In our Brisbane table, an industrial roller shutter (per door, installed) runs $2,900–$12,250, and $4,600 is typical.
How much does a commercial sectional door cost in Brisbane?
A commercial sectional overhead door (installed) is $3,500–$20,200 in our Brisbane table, typically $9,900.
How much does a high-speed door cost in Brisbane?
A high-speed or rapid-roll door (supply and install) is $11,200–$25,500 in our Brisbane table, typically $15,300.
How much do insulated commercial garage doors cost in Brisbane?
In Brisbane, insulated PU-core door panels are priced by area at $280–$380 per square metre of door, ex GST and supply only, typically $330 per square metre. Built into a finished sectional overhead door, the installed price is $3,500–$20,200 ex GST. Through humid Brisbane summers the insulation mainly keeps heat out of air-conditioned showrooms, workshops and food storage.
How do roller door sizes change the price for a Brisbane business?
For a Brisbane business, a motorised roller door around 3m x 3m costs $3,275–$5,600 installed, around 4m x 4m costs $4,700–$7,650 installed, and around 5m x 5m costs $6,100–$10,200 installed. Choosing a manual door at the smallest size brings it down to $2,050–$3,675 installed. The bigger sizes suit truck and container access at industrial sites around Eagle Farm or Acacia Ridge.
What is included in commercial garage door installation in Brisbane?
A Brisbane commercial door installation price normally covers the door, guides and drum or tracks, fixing to the existing structure, and commissioning the motor and safety beams. Sectional doors at $3,500–$20,200 installed and rapid-roll doors at $11,200–$25,500 supply and install are quoted ex GST, so add GST before comparing totals. Removing an old door, new steel framing, electrical runs and work outside business hours are usually separate lines.
What does replacing a commercial door motor cost in Brisbane?
Swapping out a failed motor or operator on a Brisbane commercial door is $765–$2,550 per door, with $1,275 per door typical. Light single-phase units on small roller doors fall at the lower end; heavy-duty three-phase operators on wide shutters at Eagle Farm or Rocklea warehouses sit near the upper end. Summer storms and humidity are hard on control boards and limit switches, so the replacement price should include new remotes or wall controls, safety beams reconnected, and the limits set so the curtain stops cleanly at the floor.
What pushes a Brisbane roller shutter quote toward the upper end?
An industrial roller shutter in Brisbane spans $2,900–$12,250 installed because the row covers everything from a modest storeroom door to a wide truck opening. Width and height matter first, then curtain gauge, then the operator: a manual chain-hoist shutter on a small opening sits low, while a motorised door with a heavier curtain, wind locks for exposed storm-season sites, and a three-phase operator for constant cycling lands high. Crane hire for a tall door and removal of the old curtain are the usual extras to confirm on the quote.
How much does yearly servicing cost for commercial doors in Brisbane?
Brisbane businesses budget $155–$355 a year for each door on an annual service, and $255 is the common figure. The visit covers spring tension, guide cleaning and lubrication, bearing wear, motor limits and the safety reversing test. Humid summers and afternoon storms leave grit and moisture in guides and electrical housings, so doors at wet, exposed sites benefit from the full check rather than a quick look. Multiply the per-door figure by the number of doors on site to set a yearly maintenance line.

Advertise with us

Reach Australian businesses researching commercial service costs. Fill in your details and we'll be in touch within 1 business day.

Thanks! We'll be in touch

Expect a reply within 1 business day.

Got a question about costs?
Chat with Sam
Sam the Platypus
Online now
Powered by What's The Damage