Independent Australian Cost Guides
Updated November 2026
← All commercial trades

How much do commercial garage doors cost in Newcastle?

Commercial garage doors run $2,900–$25,500
installed, depending on door type, size and automation
In Newcastle, an installed industrial roller shutter starts at $2,900 and a rapid-roll door, supplied and installed, reaches $25,500. For a Cardiff fabrication shop, a sectional overhead door runs $3,500–$20,200 installed, and a manual roller door for an opening near 3m x 3m is $2,050–$3,675 installed.
+5.1% Commercial garage door prices are up around 5.1% over the past year, re-verified against 90+ sources in November 2026. Year on year
Typical Industrial Roller Shutter
$4,600
per commercial roller door, installed
Roller Shutter
$2,900–$12,250
Insulated
$280–$380/m²
Sectional
$3,500–$20,200
Roller $2,900Sectional $9,900High-speed $25,500

Installed, a commercial garage door in Newcastle runs $2,900–$25,500: industrial roller shutters at the lower end, commercial sectional doors through the middle and high-speed rapid-roll doors at the upper end. Opening size and duty decide where each job sits, since a door that opens a few times a day needs a lighter motor than one on a busy depot.

Newcastle's commercial doors serve mining-service workshops, fabrication shops and transport yards across the lower Hunter, port businesses around Carrington and Kooragang, and trade units in suburbs from Kotara to Wallsend. Heavy-cycle doors wear their motors fastest, and a motor or operator replacement costs $765–$2,550 per door.

Servicing runs $155–$355 a year for each door. GST is included in roller door and shutter prices; sectional, insulated-panel and rapid-roll prices are ex GST. For a 5m x 5m opening, a motorised roller door runs $6,100–$10,200 installed.

Comparing cities, or after the Australia-wide picture? See the national guide: How much do commercial garage doors cost in Australia?

Quick answerA commercial garage door costs $2,900–$25,500 installed depending on type — roller shutters at the low end, high-speed rapid-roll doors at the top. Get free commercial quotes →

Commercial Garage Door Prices in Newcastle 2026: Cost Table and Price List

ServiceLowTypicalHigh
Industrial roller shutter (per door, installed)$2,900installed$4,600$12,250
Insulated commercial door (PU-core sectional, supply only, per sqm of door, ex GST)$280/sqm$330$380
Commercial sectional overhead door (installed, ex GST)$3,500installed$9,900$20,200
High-speed / rapid-roll door (supply + install, ex GST)$11,200supply+install$15,300$25,500
Roller door ~3m x 3m, manual (installed)$2,050installed$2,700$3,675
Roller door ~3m x 3m, motorised (installed)$3,275installed$4,275$5,600
Roller door ~4m x 4m, motorised (installed)$4,700installed$5,800$7,650
Roller door ~5m x 5m, motorised (installed)$6,100installed$7,450$10,200
Door motor / operator replacement$765per door$1,275$2,550
Annual door service (per door)$155per year$255$355
Step 1 of 2

What do you need a callback about?

One tap — we'll show you the going rate, then take your number.

You're in.

A local installer will be in touch about your job. No spam, no call centre.

Scoping a commercial garage door? Get a quote from an Australian commercial door installer — free, no obligation.

Get commercial quotes →
Prices verified November 2026 · Cross-referenced against Australian commercial garage door suppliers · See methodology

Prices include GST unless the row says ex GST. Newcastle-wide, November 2026. Large or custom openings vary.

Average installation cost of commercial roller doors and garage doors in Newcastle

What is the average installation cost for commercial roller doors? In Newcastle the typical industrial roller shutter comes in at $4,600 installed, inside a band of $2,900–$12,250 installed, and the typical motorised 3 m x 3 m roller door at $4,275 installed, inside $3,275–$5,600 installed. Those two figures cover most of the doors going onto the Steel River, Sandgate and Beresfield sheds. The average moves with size: a 4 m x 4 m motorised door typically costs $5,800 installed and a 5 m x 5 m door $7,450 installed.

The other door types sit in their own bands. A commercial sectional overhead door, the choice for a Broadmeadow car yard or a Charlestown shopfront, is $3,500–$20,200 installed, ex GST. A high-speed rapid-roll door for the food and cold-storage sites near Tomago is $11,200–$25,500 supply and install, ex GST. Insulated PU-core door panels are priced on area at $280–$380 per m² of door, supply only, ex GST, with fitting quoted on top.

Two smaller jobs round out the list: an operator replacement at $765–$2,550 per door, and an annual service at $155–$355 a year for each door, cheap insurance on a shed where the westerlies drive grit into the guides.

Use the form on this page to get quotes from commercial garage door installers in Newcastle.

Commercial vs residential garage doors — why commercial costs more

A garage door on a Merewether house runs a few times a day and closes one car bay. A door at a Hexham freight depot or a Steel River fabrication shop may open every few minutes for trucks and forklifts, so the curtain, springs, drum and operator are rated for heavy duty. Commercial openings are larger, often three-phase powered and built tall enough for trucks, and install crews bring lifting gear and may work around shift changes, costs a residential job never carries.

Commercial garage door sizes and how size drives price

Size moves a Newcastle quote first. A motorised roller door near 3m x 3m costs $3,275–$5,600 installed, near 4m x 4m $4,700–$7,650, and near 5m x 5m $6,100–$10,200. Larger truck openings move into industrial roller shutters. As the opening grows, the curtain gets heavier, the spring barrel and drum get bigger and the operator steps up a class. On busy depot floors, ask for steel guide protectors or bollards in the same quote, since a forklift strike on a guide can put a big door out of action.

What Actually Moves the Commercial Garage Door Cost in Newcastle

How to Keep the Commercial Garage Door Cost Sane in Newcastle

1
Tell installers how many times a day each door opens, so the operator is sized to the real count rather than the largest on offer.
2
Ask for brush or wiper seals on the guides at dusty sites; cleaner guides mean less wear on the curtain and fewer call-outs.
3
Keep a sound curtain and drum and replace only the operator, at $765–$2,550 per door, when the motor is the part that has failed.
4
Service doors yearly at $155–$355 a year per door, and book extra visits for doors exposed to salt or coal dust near the port.
5
Ask whether a sound manual door can be motorised instead of replaced; adding an operator usually costs less than a new motorised door.

Commercial garage door cost by door type

Quick answerNewcastle prices: an industrial roller shutter costs $2,900–$12,250 installed, a commercial sectional overhead door $3,500–$20,200 installed ex GST and a high-speed rapid-roll door $11,200–$25,500 supplied and installed ex GST.

For most Newcastle sites the choice sits between a shutter and a sectional. A shutter is the tougher, lower-cost door for depots and fabrication bays, where dust, knocks and security matter more than looks. A sectional costs more but suits customer-facing frontages, and its insulated version suits offices and gyms with air-conditioning. A rapid-roll door is a specialist addition, usually inside a building on an opening that forklifts cross all shift. Coastal or dusty exposure lifts the price of whichever type is chosen.

Our Methodology

Commercial pricing on this page is compiled from Australian commercial and industrial garage-door suppliers and installers, published supplier price guides and product ranges as of November 2026. We cross-reference ranges from multiple sources; no contractor can influence a published figure. All prices are estimates, GST-inclusive unless a row says ex GST, and will vary with your specific opening, door spec and site. Always get multiple written quotes. Last reviewed November 2026. Read our full methodology →

Commercial garage door prices, product by product

Industrial roller shutters cost $2,900–$12,250 installed in Newcastle, typically $4,600. A single bay on a Cardiff trade unit sits in the lower half; a wide truck entry at a Hexham freight depot, with a heavy curtain, wind locks and a three-phase drive, sits near the upper figure. Curtain finish matters near salt water.

Commercial sectional overhead doors run $3,500–$20,200 installed ex GST, typically $9,900. The insulated version is $280–$380 per m² of door, supply only and ex GST; a door about 3m wide and 3m high is roughly nine m² of door, or $2,520–$3,420 supplied, with installation quoted on top.

Rapid-roll doors are $11,200–$25,500 supplied and installed ex GST, typically $15,300. They suit food processing, beverage and cold storage sites where a slow door would hold up forklifts and leak chilled air. Activation by radar or floor loop, the curtain type and whether the door faces the weather all move the figure.

A replacement operator costs $765–$2,550 per door, with the price depending mostly on door weight and how often it runs. Yearly servicing at $155–$355 a year per door usually works out cheaper than an emergency call-out when a door jams open on a busy depot, and it catches worn springs before they fail.

Commercial garage doors — go deeper

Which door for which job?

Fabrication shops, freight depots and machinery sheds at Beresfield and Tomago: an industrial roller shutter takes knocks, locks up well and costs the least installed for a big opening.

Showrooms, gyms and offices with cooled or heated space around Kotara and Cardiff: a sectional door, insulated where the room is air-conditioned, gives a neater frontage and a better seal.

Food, beverage and cold storage sites: a rapid-roll door on busy internal openings, and a shutter or sectional on the outside wall to secure the building after hours.

Red flags when comparing commercial door installers

Roller door sizes and prices in Newcastle

In Newcastle, roller doors close everything from fabrication bays at Beresfield to trade units at Cardiff and depots near the port. A 3m x 3m door costs $2,050–$3,675 installed as a hand-lifted door and $3,275–$5,600 installed with a motor. Light trucks fit through about 4m x 4m, which is $4,700–$7,650 installed, and a rigid truck through about 5m x 5m, at $6,100–$10,200 installed.

Where a quote lands inside each row comes down to the work the door does. A shop running forklifts in and out all shift is often quoted with a heavier curtain and an operator rated for frequent cycles, both of which push toward the upper figure. Doors that take regular knocks tend to be priced as an industrial roller shutter instead, at $2,900–$12,250 installed, typically $4,600, where curtain gauge and width decide the figure.

Multi-bay sites multiply quickly. Four motorised doors of about 4m x 4m on one Hexham warehouse come to $18,800–$30,600 installed, working from $4,700–$7,650 each, before a yearly service of $155–$355 per door. Dust and grit around the industrial suburbs wear guide tracks and bearings, which is why a regular service helps push operator replacement, $765–$2,550 per door, further off.

Commercial garage door cost in Newcastle for industrial and trade sites

Commercial garage doors in Newcastle cost $2,900–$12,250 installed for an industrial roller shutter, typically $4,600. A commercial sectional overhead door costs $3,500–$20,200 installed ex GST, typically $9,900. Smaller trade units with a motorised roller door around 3m x 3m pay $3,275–$5,600 installed, and a 5m x 5m motorised roller door costs $6,100–$10,200 installed.

The Hunter's industrial base drives much of the work. Fabrication shops, mine-service workshops and depots in Beresfield, Tomago, Mayfield West and Cardiff need wide doors that cycle all day and stand up to dust and grit. High-speed rapid-roll doors, at $11,200–$25,500 supplied and installed ex GST, are used on busy internal openings and food sites. Closer to the coast in Carrington, Wickham and Merewether, salt air speeds up corrosion of curtains and tracks, so galvanised or coated finishes earn their cost.

Motors are a frequent failure on high-use doors, with replacement costing $765–$2,550 per door, and an annual service is $155–$355 a year per door. A Newcastle commercial door quote should list the door type and opening size, the curtain or panel gauge, motor duty for the expected daily cycles, safety beams and controls, protection for coastal or dusty sites, and whether figures include GST.

What a Compliant Commercial Garage Door Quote Includes — Cost in Newcastle

Newcastle commercial garage door quotes should spell out salt protection near the harbour, access on industrial sites around Mayfield and the GST basis of each figure. Compare only once every quote describes the same door on the same terms.

Garage door cost in Newcastle: commercial garage door prices job by job

Garage door cost in Newcastle depends on what the door has to do, so garage door prices are easiest to read as a list of jobs. These are the figures for commercial work across the city, from a single trade unit at Wallsend to a transport yard at Hexham.

Use the form on this page to get quotes from commercial garage door installers in Newcastle.

Frequently Asked Questions — Commercial Garage Door Cost in Newcastle

How much is an industrial roller door for a Newcastle workshop?
An industrial roller shutter for a Newcastle workshop or depot costs $2,900–$12,250 installed, typically $4,600 installed. Large truck openings at Tomago or Beresfield sit near the top, with a heavier curtain and an industrial operator. Grit from heavy industry wears guides and bearings, so ask what brushes or seals are fitted to the guides and whether a service plan is offered.
What does an overhead sectional door cost in Newcastle?
An overhead sectional door for a Newcastle commercial site costs $3,500–$20,200 installed, ex GST, typically $9,900 ex GST. The panels lift up and back along ceiling tracks, so the building needs clear headroom above the opening. Sectionals suit showrooms and workshops that want windows or insulation, and wide insulated doors with glazing cost the most.
What do commercial door installers charge in Newcastle?
Going by our Newcastle table, expect $3,275–$5,600 installed for a motorised roller door about 3 m x 3 m, $3,500–$20,200 installed for a commercial sectional overhead door and $2,900–$12,250 installed for an industrial roller shutter.
What does a new commercial door opener cost in Newcastle?
A new opener or motor for a commercial door in Newcastle costs $765–$2,550 per door. Light operators for small roller doors sit at the low end, and heavy-duty units for wide shutters or sectionals that cycle all day sit at the top. The price should include remotes or a wall button, safety beams, setting the travel limits and testing the safety reversing function.
What does a single roller door cost for a small Newcastle trade unit?
A single manual roller door around 3m x 3m for a small Newcastle trade unit costs $2,050–$3,675 installed, typically $2,700 installed. That price covers the curtain, guides, drum and fitting into an existing opening. Removing an old door, new framing and a motor are extra, and motorising the same size takes it to $3,275–$5,600 installed.
What does annual servicing cost for commercial doors near Newcastle's port?
Servicing a commercial door in Newcastle costs $155–$355 per year for each door, and a typical visit is $255 per year. Doors at Carrington, Mayfield and Kooragang face salt air off the harbour and fallout from heavy industry, both hard on guides, springs and bearings. A good service cleans and lubricates those parts, checks spring tension and confirms the door stops and reverses when obstructed.
What does a rapid-roll high-speed door cost for a Newcastle warehouse?
In Newcastle a high-speed rapid-roll door is $11,200–$25,500 supply and install, ex GST, with $15,300 the usual figure. Logistics sheds at Beresfield and Thornton, food distributors and cold stores run them on busy internal openings where a fast fabric curtain keeps dust, draughts and warm air out while forklifts stream through. Curtain speed, opening size, a vision panel and the trigger method all move the figure; a wind-rated curtain for an external opening facing the coast at Kooragang sits toward the upper end.
How much do insulated commercial door panels cost in Newcastle?
Supply only and ex GST, insulated PU-core panels in Newcastle run $280–$380 a square metre of door, with $330 a square metre typical. Because panels are priced by area, a wide dock door takes a lot more panel than a single van opening. Tracks, springs, the operator and fitting are charged separately, and as a complete installed sectional the figure is $3,500–$20,200 ex GST. Cold stores near the port and air-conditioned showrooms at Kotara and Charlestown are the usual Newcastle buyers of insulated doors.
What do 4m and 5m motorised roller doors cost in Newcastle?
Newcastle prices for the larger roller doors are $4,700–$7,650 installed for a motorised door around 4m by 4m and $6,100–$10,200 installed for one around 5m by 5m, with $7,450 typical at the larger size. The 4m door suits vans and small trucks at Wallsend or Mayfield trade units; the 5m door is for rigid trucks, buses and boats. A heavier curtain gauge, wind locks for a site exposed to the coast and a three-phase operator for all-day cycling are what take a quote to the upper figure.

Advertise with us

Reach Australian businesses researching commercial service costs. Fill in your details and we'll be in touch within 1 business day.

Thanks! We'll be in touch

Expect a reply within 1 business day.

Got a question about costs?
Chat with Sam
Sam the Platypus
Online now
Powered by What's The Damage