Independent Australian Cost Guides
Updated November 2026
← All commercial trades

How much do commercial garage doors cost in Byron Bay?

Commercial garage doors run $2,950–$25,750
installed, depending on door type, size and automation
Around Byron Bay, an installed industrial roller shutter starts at $2,950 and a rapid-roll door, supplied and installed, reaches $25,750, with smaller roller doors coming in lower. A Bangalow shop or trade unit with an opening near 3m x 3m can expect $2,050–$3,700 for a manual roller door installed, or $3,300–$5,650 installed once it is motorised.
+5.1% Commercial garage door prices are up around 5.1% over the past year, re-verified against 90+ sources in November 2026. Year on year
Typical Industrial Roller Shutter
$4,600
per commercial roller door, installed
Roller Shutter
$2,950–$12,350
Insulated
$280–$380/m²
Sectional
$3,550–$20,400
Roller $2,950Sectional $10,000High-speed $25,750

In Byron Bay, installed prices for a commercial garage door run $2,950–$25,750, though most local jobs are roller doors toward the smaller end of that span rather than rapid-roll doors at the top. Motorised, a 3m x 3m roller door is $3,300–$5,650 installed, and width, height and the curtain finish then decide where a particular door lands.

Commercial doors in the shire go on storage and trade units in the industrial estate, rear loading doors behind restaurants and shops in town, workshops in Mullumbimby and sheds on hinterland properties. Close to the ocean, coated curtains and stainless fixings pay their way, and servicing each door at $155–$360 a year helps keep salt from seizing guides and springs.

Replacing the motor or operator is $770–$2,575 per door. Roller door and shutter prices include GST; sectional, insulated-panel and rapid-roll prices are listed ex GST, so add GST before comparing them with roller door quotes.

Comparing cities, or after the Australia-wide picture? See the national guide: How much do commercial garage doors cost in Australia?

Quick answerA commercial garage door costs $2,950–$25,750 installed depending on type — roller shutters at the low end, high-speed rapid-roll doors at the top. Get free commercial quotes →

Commercial Garage Door Prices in Byron Bay 2026: Cost Table and Price List

ServiceLowTypicalHigh
Industrial roller shutter (per door, installed)$2,950installed$4,600$12,350
Insulated commercial door (PU-core sectional, supply only, per sqm of door, ex GST)$280/sqm$330$380
Commercial sectional overhead door (installed, ex GST)$3,550installed$10,000$20,400
High-speed / rapid-roll door (supply + install, ex GST)$11,350supply+install$15,450$25,750
Roller door ~3m x 3m, manual (installed)$2,050installed$2,725$3,700
Roller door ~3m x 3m, motorised (installed)$3,300installed$4,325$5,650
Roller door ~4m x 4m, motorised (installed)$4,725installed$5,850$7,700
Roller door ~5m x 5m, motorised (installed)$6,150installed$7,500$10,300
Door motor / operator replacement$770per door$1,275$2,575
Annual door service (per door)$155per year$255$360
Step 1 of 2

What do you need a callback about?

One tap — we'll show you the going rate, then take your number.

You're in.

A local installer will be in touch about your job. No spam, no call centre.

Scoping a commercial garage door? Get a quote from an Australian commercial door installer — free, no obligation.

Get commercial quotes →
Prices verified November 2026 · Cross-referenced against Australian commercial garage door suppliers · See methodology

Prices include GST unless the row says ex GST. Byron Bay-wide, November 2026. Large or custom openings vary.

Commercial garage door types and what they cost

Industrial roller shutters

$2,950–$12,350 installed

The default for trade and storage units across the Arts and Industry Estate, and for bigger sheds around Mullumbimby. A shutter gives a wide, secure opening for the least outlay, and a coated curtain earns its cost close to the beach.

Sectional overhead doors

$3,550–$20,400 installed, ex GST

Suits a showroom, studio or fitted-out workshop in the estate where a glazed or timber-look panel door faces customers, and where a quieter lift matters next to an office or shop floor.

Rapid-roll doors

$11,350–$25,750 supply and install, ex GST

A specialist buy in the shire, justified for a food or drink producer whose cool room or packing area opens all day. For a shop storeroom used a few times an hour, a roller door does the job.

Insulated sectional doors

$280–$380 per m² of door, supply only, ex GST

Worth pricing for a cool room, wine or produce store, or an air-conditioned studio where the door makes up much of the wall, since the insulated core slows heat moving through it.

Rear access doors

quoted per door

Restaurants and shops in town often want a lockable rear door beside the delivery opening for staff and bins. Quoting it with the main door keeps the finishes matching and saves the installer a second trip.

Commercial vs residential garage doors — why commercial costs more

A house door in Suffolk Park or Ocean Shores lifts for a car or two. A door on an estate unit or a hinterland shed may let delivery vans, a forklift or a tractor through many times a day, across a bigger opening. Commercial doors use thicker curtain steel or heavier panels, springs and bearings rated for more cycles, a motor built for steady work, and safety sensors that stop the door on an obstruction. That hardware is where the extra money goes.

Commercial garage door sizes and how size drives price

Size is the first thing a Byron Bay roller door quote follows. Motorised, a door close to 3m x 3m is $3,300–$5,650 installed, close to 4m x 4m $4,725–$7,700, and close to 5m x 5m $6,150–$10,300. A manual door at the smallest size comes to $2,050–$3,700, enough for a storeroom or bike shed opened once or twice a day. Taller doors for trucks, boats or farm machinery need a stronger motor and drum, and openings beyond 5m move into industrial shutters or sectionals.

What Actually Moves the Commercial Garage Door Cost in Byron Bay

How to Keep the Commercial Garage Door Cost Sane in Byron Bay

1
Neighbours in the same estate building can share one installer visit; a combined booking spreads the travel charge across several doors.
2
Close to the beach, rinse curtains and guides with fresh water every few weeks; it slows corrosion and lengthens the life of springs.
3
Book the yearly service, $155–$360 a year per door, ahead of the summer holiday rush, when hospitality doors work hardest.
4
Show staff how the manual release works and what a loose guide or noisy bearing sounds like; catching it early costs less than a call-out.
5
A few clear photos of the opening, the drum area and the nearest power point let an installer firm up a price before driving out to a hinterland job.

Commercial garage door cost by door type

Quick answerIn Byron Bay, roller doors are the common job: a motorised 3m x 3m door costs $3,300–$5,650 installed, while an industrial roller shutter is $2,950–$12,350 installed and a sectional overhead door $3,550–$20,400 installed ex GST.

The door type fixes the range before size or finish do. Roller doors and shutters are the economical, secure choice for shops, storage units and sheds across the shire. Sectional overhead doors cost more for their panels, tracks and springs, and appeal where the door faces customers or the space is cooled. Rapid-roll doors are uncommon outside food and drink production, where the door cycles all day. Insulated sectionals are priced per square metre of door, supply only, with fitting quoted separately.

Our Methodology

Commercial pricing on this page is compiled from Australian commercial and industrial garage-door suppliers and installers, published supplier price guides and product ranges as of November 2026. We cross-reference ranges from multiple sources; no contractor can influence a published figure. All prices are estimates, GST-inclusive unless a row says ex GST, and will vary with your specific opening, door spec and site. Always get multiple written quotes. Last reviewed November 2026. Read our full methodology →

Commercial garage door prices, product by product

Industrial roller shutters cost $2,950–$12,350 installed in Byron Bay, with a typical job around $4,600. A light shutter on a single estate unit sits near the bottom; a wide, tall door for a truck or boat with a three-phase operator and wind locks heads towards the upper figure.

A commercial sectional overhead door is $3,550–$20,400 installed, ex GST, typically $10,000 ex GST. At the lower figure is a single steel panel door; at the higher, a wide door with glazing, a timber-look finish or a built-in pass door. Headroom for the tracks and the roof structure above the opening both affect the price.

An insulated PU-core sectional door costs $280–$380 per square metre of door, supply only, ex GST. A delivery door of about 3m x 3m is 9 square metres, roughly $2,520–$3,420 supplied, before installation. That money is well spent on a cool room or air-conditioned studio, less so on an open storage shed.

High-speed and rapid-roll doors cost $11,350–$25,750 supplied and installed, ex GST. In the shire they are mostly a question for food and drink producers, where a fast curtain between a cool room and a packing or loading area saves energy on every cycle. For a door opening a handful of times a day, the cost is hard to justify.

Commercial garage doors — go deeper

Which door for which job?

Storage units and trade workshops in the Arts and Industry Estate, plus larger sheds out at Mullumbimby: a roller door or shutter, motorised if it opens often and manual if it barely moves.

Showrooms, studios and shopfronts that customers see: a sectional overhead door with glazing or a timber-look finish, and insulated panels where the space is air-conditioned.

Hinterland farm sheds and machinery stores: a large shutter sized for the tallest vehicle, with a manual override so the door still opens when a storm takes out the power.

Red flags when comparing commercial door installers

Commercial garage door cost in Byron Bay for shops, sheds and industrial units

A commercial garage door in Byron Bay most often means a roller door on a shop, storage unit or light-industrial shed. A manual roller door around 3m x 3m costs $2,050–$3,700 installed, typically $2,725. Motorised, the same size runs $3,300–$5,650 installed, and a larger 4m x 4m motorised door costs $4,725–$7,700 installed, usually near $5,850.

Units in the Arts and Industry Estate and Talwood Estate, and workshops around Mullumbimby, account for much of the commercial door work, along with rear service doors on hospitality venues. Salt air close to the beach at Belongil, Wategos and Suffolk Park corrodes steel curtains, tracks and fixings faster than inland, so coastal buyers often pay for higher-grade coatings, stainless fixings and more regular servicing. An annual service is $155–$360 a year per door, and replacing a failed motor costs $770–$2,575 per door.

Bigger openings for trucks or boats move into industrial roller shutters at $2,950–$12,350 installed, or commercial sectional overhead doors at $3,550–$20,400 installed ex GST. A useful Byron Bay garage door quote should give the clear opening size, the curtain or panel material and its coating for coastal exposure, whether the door is manual or motorised, the motor model and remotes supplied, removal of the old door, and any travel charge for the installer.

What a Compliant Commercial Garage Door Quote Includes — Cost in Byron Bay

Commercial garage door quotes in Byron Bay need to pin down salt protection, access and GST treatment before a total means anything. Ask every installer to write the same door up the same way.

Frequently Asked Questions — Commercial Garage Door Cost in Byron Bay

What do commercial roller and sectional doors cost in Byron Bay?
From our Byron Bay table: $3,300–$5,650 installed for a motorised roller door about 3 m x 3 m (typically $4,325); $3,550–$20,400 installed for a commercial sectional overhead door (typically $10,000); $2,950–$12,350 installed for an industrial roller shutter (typically $4,600).
How much does a budget roller door cost in Byron Bay?
In our Byron Bay table: a manual roller door about 3 m x 3 m $2,050–$3,700 installed and the same size motorised $3,300–$5,650 installed.
How much does a commercial door motor replacement cost in Byron Bay?
A door motor or operator replacement is $770–$2,575 a door in our Byron Bay table, typically $1,275.
What does a large industrial door cost for a Byron Bay shed or workshop?
For a truck, boat or machinery opening in Byron Bay, a motorised roller door around 5m x 5m costs $6,150–$10,300 installed, typically $7,500 installed. Heavier industrial roller shutters cost $2,950–$12,350 installed, with wide, tall doors and a heavy-duty operator costing the most. For sheds in the Arts and Industry Estate or out towards Mullumbimby, confirm the opening height as well as the width, since tall doors move up the band.
Are insulated roller or panel doors worth pricing in Byron Bay?
Insulated doors are worth pricing in Byron Bay where a shop, cafe store room or workshop is air-conditioned or holds produce. PU-core panels cost $280–$380 per square metre of door, supply only and ex GST, and a complete commercial sectional door with insulated panels is $3,550–$20,400 installed, ex GST. Close to the beach at Belongil or Suffolk Park, ask for a panel finish suited to salt air.
How much does an annual commercial door service cost in Byron Bay?
Byron Bay businesses pay $155–$360 per year per door for an annual commercial door service, with $255 per year typical. The visit should cover spring tension, curtain or panel alignment, cleaning and lubricating the guides, motor limits and the safety reversing test. Doors near the surf at Wategos and Belongil collect salt in guides and bearings, and a neglected door can end in a motor replacement at $770–$2,575 per door.
What does a commercial sectional overhead door cost for a Byron Bay shop or showroom?
A commercial sectional overhead door in Byron Bay runs $3,550–$20,400 installed, ex GST, with $10,000 the typical figure. Sectionals lift up and back on tracks, so they suit retail tenancies, surf and cafe stores in the industrial estate, and workshops that want glazing or a neater look than a steel curtain. A plain single-width panel door sits near the lower figure; width, insulated panels, windows, a pass door and the operator take a quote toward the upper figure. Check the headroom above the opening before accepting a price.
How much is a 4m x 4m motorised roller door in Byron Bay?
Around 4m by 4m, a motorised roller door for a Byron Bay workshop comes to $4,725–$7,700 installed, typically $5,850. That opening handles vans, small trucks and boat trailers at workshops in the Byron Arts and Industry Estate and sheds out toward Mullumbimby. Salt air off Belongil and Wategos beaches is hard on guides and springs, so ask whether the quoted curtain and fixings carry a coastal finish. The installed figure normally covers the door, drum, guides, motor and safety beams fitted to a sound existing opening.
What does a high-speed door cost for a Byron Bay food or produce business?
A high-speed rapid-roll door in Byron Bay costs $11,350–$25,750 supply and install, ex GST, and $15,450 is typical. Breweries, bakeries, produce packers and cold rooms use them on internal openings where staff and forklifts move constantly and a fast fabric curtain keeps cooled air in and insects out. The quote should state the opening size, curtain speed, activation method and whether the frame is stainless or galvanised for a wet, salty environment. Smaller internal openings sit low; wide external doors with wind-rated curtains sit high.

Advertise with us

Reach Australian businesses researching commercial service costs. Fill in your details and we'll be in touch within 1 business day.

Thanks! We'll be in touch

Expect a reply within 1 business day.

Got a question about costs?
Chat with Sam
Sam the Platypus
Online now
Powered by What's The Damage