Independent Australian Cost Guides
Updated November 2026
← All commercial trades

How much do commercial garage doors cost in Townsville?

Commercial garage doors run $3,000–$26,250
installed, depending on door type, size and automation
Townsville's $3,000–$26,250 buys one door, an installed industrial roller shutter at the bottom and a rapid-roll door, supply and install, at the top. A Bohle depot needing a motorised roller door for a 5m x 5m opening faces $8,200–$12,400 installed, and a sectional overhead door is $3,600–$20,800 installed.
+5.2% Commercial garage door prices are up around 5.2% over the past year, re-verified against 90+ sources in November 2026. Year on year
Typical Industrial Roller Shutter
$4,750
per commercial roller door, installed
Roller Shutter
$3,000–$12,600
Insulated
$290–$390/m²
Sectional
$3,600–$20,800
Roller $3,000Sectional $10,200High-speed $26,250

Townsville prices for a commercial garage door run $3,000–$26,250 installed, from an industrial roller shutter at the lower end to a high-speed rapid-roll door at the top. Size, motorisation and the wind-resistance features specified decide the price within each type; a manual 3m x 3m roller door is $3,300–$5,000 installed.

Most commercial doors in the city are on sheds, depots and workshops in the Bohle and Garbutt industrial areas and around the port, with security shutters on shopfronts in Aitkenvale, Kirwan and the CBD. Storms and humidity in the wet season are hard on springs, motors and guides, so servicing is best done before the wet starts.

That service costs $155–$365 a year for each door, and a replacement motor $785–$2,625 per door. Sectional, insulated and rapid-roll prices are ex GST; roller door and shutter prices include GST.

Comparing cities, or after the Australia-wide picture? See the national guide: How much do commercial garage doors cost in Australia?

Quick answerA commercial garage door costs $3,000–$26,250 installed depending on type — roller shutters at the low end, high-speed rapid-roll doors at the top. Get free commercial quotes →

Commercial Garage Door Prices in Townsville 2026: Cost Table and Price List

ServiceLowTypicalHigh
Industrial roller shutter (per door, installed)$3,000installed$4,750$12,600
Insulated commercial door (PU-core sectional, supply only, per sqm of door, ex GST)$290/sqm$340$390
Commercial sectional overhead door (installed, ex GST)$3,600installed$10,200$20,800
High-speed / rapid-roll door (supply + install, ex GST)$11,550supply+install$15,750$26,250
Roller door ~3m x 3m, manual (installed)$3,300installed$4,000$5,000
Roller door ~3m x 3m, motorised (installed)$4,550installed$5,600$7,000
Roller door ~4m x 4m, motorised (installed)$6,400installed$7,600$9,400
Roller door ~5m x 5m, motorised (installed)$8,200installed$9,500$12,400
Door motor / operator replacement$785per door$1,300$2,625
Annual door service (per door)$155per year$260$365
Step 1 of 2

What do you need a callback about?

One tap — we'll show you the going rate, then take your number.

You're in.

A local installer will be in touch about your job. No spam, no call centre.

Scoping a commercial garage door? Get a quote from an Australian commercial door installer — free, no obligation.

Get commercial quotes →
Prices verified November 2026 · Cross-referenced against Australian commercial garage door suppliers · See methodology

Prices include GST unless the row says ex GST. Townsville-wide, November 2026. Large or custom openings vary.

Commercial garage door types and what they cost

Industrial roller shutters

$3,000–$12,600 installed

The default on transport depots, mining-services yards and storage sheds at Bohle, Garbutt and Stuart. In Townsville a shutter is often ordered with wind locks and a heavier curtain, because the most common way a roller door fails in strong wind is the curtain disengaging from its guides.

Sectional overhead doors

$3,600–$20,800 installed, ex GST

Panel doors suit vehicle showrooms and trade counters along Ingham Road and in Garbutt, and workshops beside offices, where a quieter, better-sealed door keeps dust and noise out. A door this large has to resist wind pressure both inward and outward.

Rapid-roll doors

$11,550–$26,250 supplied and installed, ex GST

Worth pricing for cold stores and food distributors sending chilled freight out to North Queensland towns, where a fast fabric curtain on an internal opening keeps cooled air in through a long, humid wet season.

Insulated sectional doors

$290–$390 per m² of door, supply only, ex GST

Double-skin PU-core doors pay their way where a Townsville door closes off cooled space: a dock serving a cold room, a medical or laboratory store, or an air-conditioned workshop whose door faces the western sun.

Pedestrian access doors

quoted per door

A steel door beside a large opening lets staff come and go without running the main door, saving wear on its motor and springs. Price it on the same order and ask how its frame and lock are fixed to handle the same wind loads.

Commercial vs residential garage doors — why commercial costs more

A house door on a Townsville home lifts a few times a day. A door on a Bohle transport depot or a port-side warehouse may open dozens of times a shift, across a much wider span, with forklifts and trucks working through it. That means thicker curtain steel, heavier springs and drums, a motor rated for continuous work and safety devices that stop the door on contact. Because Townsville sits in wind region C, new doors must comply with AS/NZS 4505, so each one has to be rated for the building's design wind pressure.

Commercial garage door sizes and how size drives price

Size sets most of a roller door price. In Townsville a motorised door of about 3m x 3m runs $4,550–$7,000 installed, about 4m x 4m $6,400–$9,400 and about 5m x 5m $8,200–$12,400. The largest of those has almost three times the curtain area of the smallest, and in cyclone country the guides, fixings and wind locks grow with it. A manual 3m door at $3,300–$5,000 suits a storage bay that opens once a day. Openings wider than about 5m move into industrial shutters, sectionals or a custom build.

What Actually Moves the Commercial Garage Door Cost in Townsville

How to Keep the Commercial Garage Door Cost Sane in Townsville

1
Book the annual service in the dry months, before cyclone season opens in November, so worn springs and loose guides are fixed before the first storms.
2
If an older shed door is not wind-rated, price a permanent or removable bracing system first; removable wind-brace posts go in when a cyclone warning is issued.
3
Keep new doors to the existing openings where the trucks still fit; widening an opening brings new structural steel and making good into the bill.
4
Fit bollards or guide protectors beside doors that forklifts and trucks pass through all shift; a clipped guide can stop a curtain running true.
5
Where the existing operator is sound and rated for the new door's weight, ask whether it can be refitted; a replacement motor runs $785–$2,625 per door.

Commercial garage door cost by door type

Quick answerIn Townsville an industrial roller shutter costs $3,000–$12,600 installed, a commercial sectional overhead door $3,600–$20,800 installed ex GST, and a high-speed rapid-roll door $11,550–$26,250 supplied and installed ex GST.

Door type sets the price band before size or finish do. Shutters cost least because a rolled steel curtain and drum are simple to build, fit and repair, which is why they are the usual choice on sheds at Bohle and Stuart. Sectionals cost more for their panels, tracks and torsion springs, but they seal better and suit a glazed street frontage. Rapid-roll doors add sensors, controls and a fabric curtain built to cycle all day, mostly on internal openings. In Townsville, meeting AS/NZS 4505 adds cost to whichever type closes an external opening.

Our Methodology

Commercial pricing on this page is compiled from Australian commercial and industrial garage-door suppliers and installers, published supplier price guides and product ranges as of November 2026. We cross-reference ranges from multiple sources; no contractor can influence a published figure. All prices are estimates, GST-inclusive unless a row says ex GST, and will vary with your specific opening, door spec and site. Always get multiple written quotes. Last reviewed November 2026. Read our full methodology →

Commercial garage door prices, product by product

Industrial roller shutters run $3,000–$12,600 installed in Townsville, with a typical door at $4,750. The low end is a modest opening with a chain hoist or a single-phase motor; the high end is a wide, tall curtain with a three-phase operator, wind locks along both edges and guides bolted to steel framing. Ask for the wind rating in writing, since the curtain, guides and fixings work together to keep the door in its tracks.

A commercial sectional overhead door is $3,600–$20,800 installed, ex GST, typically $10,200 ex GST. The band runs from a single steel panel door on a trade unit to a wide, glazed door on a vehicle showroom. Panels travel on tracks under the roof, so check that the roof framing can carry the track hangers.

An insulated PU-core sectional door is priced at $290–$390 per square metre of door, supply only and ex GST. A 4m x 4m door, 16 square metres, comes to about $4,640–$6,240 supplied, before installation. In Townsville the payback comes from keeping heat out of a cooled store or a dock beside a cold room.

High-speed and rapid-roll doors cost $11,550–$26,250 supplied and installed, ex GST. They belong on internal openings between a loading dock and a chilled or clean room, where the door may cycle hundreds of times a shift. A quote in this band normally covers the drive, control box, sensors and flexible curtain; ask whether it also covers the power supply, interlocks with dock levellers and a service plan.

Commercial garage doors — go deeper

Which door for which job?

Haulage yards, mine-supply businesses and storage sheds at Bohle, Stuart and around the port: a wind-rated roller shutter, sized for the largest truck or machine that will use the opening, gives the most door for the money.

Showrooms, workshops and trade counters at Garbutt and Hyde Park: a sectional door, glazed where the street frontage matters and insulated where the space is air-conditioned, with the roof framing checked for its tracks.

Cold stores, food distribution and port logistics: a rapid-roll door on the internal opening for speed, with a wind-rated shutter or sectional closing the external opening when a cyclone warning is issued.

Red flags when comparing commercial door installers

Commercial roller shutter cost in Townsville for cyclone-prone sites

An industrial roller shutter in Townsville costs $3,000–$12,600 installed, with a typical door near $4,750. Lighter roller doors are priced by size: a manual door around 3m x 3m costs $3,300–$5,000 installed, a motorised one of that size $4,550–$7,000 installed, and a motorised 5m x 5m door $8,200–$12,400 installed.

Townsville sits in cyclone country, and roller shutters on sheds and depots in Bohle, Garbutt, Mount Louisa and the port area are often ordered with heavier curtains, wind locks and reinforced guides, which pushes jobs up the range. Wet-season downpours and humid air then work on springs, axles and motors. Shops and offices in Aitkenvale, Kirwan and North Ward use roller shutters for after-hours security as well. Where a crane rail or mezzanine blocks the drum, a commercial sectional overhead door at $3,600–$20,800 installed ex GST is the usual alternative.

Replacement motors cost $785–$2,625 per door and an annual service runs $155–$365 a year per door, ideally booked before the wet season. A good Townsville roller shutter quote should give the opening size and curtain profile, the wind locks or bracing included, the guide and fixing details, manual or motorised operation with a backup option, and whether the old shutter is removed and disposed of.

What a Compliant Commercial Garage Door Quote Includes — Cost in Townsville

Townsville commercial garage door quotes should state the cyclone specification, the booking window around the wet season and the GST basis of every figure. Without those three, two quotes for the same shed cannot be compared.

Frequently Asked Questions — Commercial Garage Door Cost in Townsville

How much do roller shutters cost in Townsville?
Townsville roller shutter prices run $3,000–$12,600 installed, with $4,750 installed typical. A plain manual shutter on a modest opening sits low in that range. Bracing a wide door against cyclone-season winds, with wind locks, a heavier curtain and stronger guide fixings, moves it higher, so ask each installer to list those features before comparing prices.
What does an insulated dock door cost per square metre in Townsville?
In our Townsville table, an insulated PU-core sectional door (supply only) runs $290–$390 a square metre, and $340 is typical.
What does a 4 or 5 metre roller door cost in Townsville?
In our Townsville table the figures are $4,550–$7,000 installed for a motorised roller door about 3 m x 3 m (typically $5,600), $6,400–$9,400 installed for about 4 m x 4 m (typically $7,600) and $8,200–$12,400 installed for about 5 m x 5 m (typically $9,500).
What does a commercial door repair or new motor cost in Townsville?
In Townsville, replacing a failed commercial door motor costs $785–$2,625 per door, typically $1,300 per door. Smaller repairs to springs, guides and bearings cost less and often surface during an annual service at $155–$365 per year per door. Wet-season humidity and storms are hard on motors and control boards, so ask whether a replacement includes battery backup for power cuts.
What does a sectional overhead door cost in Townsville?
A commercial sectional overhead door in Townsville costs $3,600–$20,800 installed, ex GST, typically $10,200 ex GST. Sectionals lift on tracks under the roof, which suits showrooms in Garbutt or Mount Louisa wanting windows, and sites where staff want a quieter door than a shutter. Large sectionals facing cyclone-season winds are braced more heavily, which lifts the price.
How much is a high-speed door for a Townsville warehouse?
A high-speed door in Townsville costs $11,550–$26,250 supply and install, ex GST, typically $15,750 supply and install. These doors suit internal openings at cold stores, food distribution and port logistics sites, where a fast fabric curtain keeps cooled air inside. Ask whether the quote includes the sensors, warning lights or interlocks a busy dock may want.
What does a 6m wide roller door cost in Townsville?
The largest roller door priced for Townsville is a motorised door around 5m by 5m at $8,200–$12,400 installed, typically $9,500. An opening of 6m or more falls outside the roller door rows on this page and is best priced against the industrial roller shutter row at $3,000–$12,600 installed, where width, curtain gauge, wind locks for cyclone-season gusts and a three-phase operator set the figure. Transport yards at Bohle and Stuart with wide truck openings should ask for the shutter row to be quoted, not a stretched roller door.
Is a manual roller door enough for a Townsville shop or storeroom?
For a Townsville shop rear door or storeroom around 3m by 3m, a manual roller door is $3,300–$5,000 installed and the motorised version is $4,550–$7,000 installed. A Kirwan or Aitkenvale retailer opening once or twice a day for deliveries can run a manual curtain; a door used constantly through a hot, humid day is better motorised so staff are not hauling a heavy curtain. Whichever you choose, ask about wind-locked guides, since a loose curtain is the usual casualty in a cyclone-season blow.
What extra costs come with a commercial door installation in Townsville?
Beyond the installed figure, such as $6,400–$9,400 for a motorised roller door around 4m by 4m or $3,600–$20,800 ex GST for a sectional overhead door, a Townsville quote can add wind locks and heavier guides for cyclone-season exposure, stainless or coated fixings against salt and humidity, a crane for a tall door, removal of the old door, a new lintel and a three-phase power run. Ask each installer to list those lines separately so quotes for Garbutt or Mount Louisa premises are compared on the same scope.

Advertise with us

Reach Australian businesses researching commercial service costs. Fill in your details and we'll be in touch within 1 business day.

Thanks! We'll be in touch

Expect a reply within 1 business day.

Got a question about costs?
Chat with Sam
Sam the Platypus
Online now
Powered by What's The Damage