Independent Australian Cost Guides
Updated November 2026
← All commercial trades

How much do commercial garage doors cost in Hobart?

Commercial garage doors run $2,750–$24,250
installed, depending on door type, size and automation
Hobart door quotes begin at $2,750 for an installed industrial roller shutter and finish at $24,250 for a high-speed rapid-roll door, supplied and installed. A Brighton workshop upgrading to a motorised roller door near 3m x 3m sees $3,100–$5,350 installed, and a sectional overhead door is $3,350–$19,200 installed.
+5.0% Commercial garage door prices are up around 5.0% over the past year, re-verified against 90+ sources in November 2026. Year on year
Typical Industrial Roller Shutter
$4,400
per commercial roller door, installed
Roller Shutter
$2,750–$11,650
Insulated
$285–$390/m²
Sectional
$3,350–$19,200
Roller $2,750Sectional $9,400High-speed $24,250

Commercial garage doors in Hobart cost $2,750–$24,250 installed; industrial roller shutters open the range and high-speed rapid-roll doors close it, with size and automation deciding the price within each type. Motorised, a roller door for a 4m x 4m opening runs $4,475–$7,300 installed.

Hobart's industrial and trade sites follow the Derwent, from Moonah, Derwent Park and Glenorchy on the western shore to Cambridge and Mornington on the eastern side, with Kingston to the south. Cold, damp months are the local factor: insulated panels at $285–$390 per m² supplied suit heated workshops, and seals and springs need regular attention.

Servicing costs $145–$340 a year for each door, and replacing a worn motor $730–$2,425 per door. GST is included in roller door and shutter prices; sectional, insulated-panel and rapid-roll prices are ex GST.

Comparing cities, or after the Australia-wide picture? See the national guide: How much do commercial garage doors cost in Australia?

Quick answerA commercial garage door costs $2,750–$24,250 installed depending on type — roller shutters at the low end, high-speed rapid-roll doors at the top. Get free commercial quotes →

Commercial Garage Door Prices in Hobart 2026: Cost Table and Price List

ServiceLowTypicalHigh
Industrial roller shutter (per door, installed)$2,750installed$4,400$11,650
Insulated commercial door (PU-core sectional, supply only, per sqm of door, ex GST)$285/sqm$335$390
Commercial sectional overhead door (installed, ex GST)$3,350installed$9,400$19,200
High-speed / rapid-roll door (supply + install, ex GST)$10,650supply+install$14,550$24,250
Roller door ~3m x 3m, manual (installed)$1,950installed$2,575$3,500
Roller door ~3m x 3m, motorised (installed)$3,100installed$4,075$5,350
Roller door ~4m x 4m, motorised (installed)$4,475installed$5,550$7,300
Roller door ~5m x 5m, motorised (installed)$5,850installed$7,100$9,700
Door motor / operator replacement$730per door$1,225$2,425
Annual door service (per door)$145per year$245$340
Step 1 of 2

What do you need a callback about?

One tap — we'll show you the going rate, then take your number.

You're in.

A local installer will be in touch about your job. No spam, no call centre.

Scoping a commercial garage door? Get a quote from an Australian commercial door installer — free, no obligation.

Get commercial quotes →
Prices verified November 2026 · Cross-referenced against Australian commercial garage door suppliers · See methodology

Prices include GST unless the row says ex GST. Hobart-wide, November 2026. Large or custom openings vary.

Roller doors in Hobart: commercial garage door costs by door type

Roller doors in Hobart are the door most businesses end up with. A manual 3 m x 3 m roller door is $1,950–$3,500 installed, a motorised one $3,100–$5,350 installed, and the larger motorised sizes the transport yards at Bridgewater and Brighton order are $4,475–$7,300 installed at about 4 m x 4 m and $5,850–$9,700 installed at about 5 m x 5 m. An industrial roller shutter with a heavier curtain for a Moonah or Mornington fabrication shop is $2,750–$11,650 installed.

Sectional overhead doors cost $3,350–$19,200 installed, ex GST. They suit the car dealers on the Brooker Highway and the Kingston trade showrooms, and glazed panels bring daylight into a workshop on a short winter afternoon.

Two door types answer Hobart's cold rather than its traffic. An insulated PU-core door at $285–$390 per m² of door, supply only, ex GST, keeps a heated workshop warm with the door shut, and a high-speed rapid-roll door at $10,650–$24,250 supply and install, ex GST, limits how long a chiller stands open at the salmon processors near the airport at Cambridge. Allow $145–$340 a year for each door serviced and $730–$2,425 per door if the operator has to be replaced.

Use the form on this page to get quotes from commercial garage door installers in Hobart.

Commercial vs residential garage doors — why commercial costs more

A Hobart house door opens a few times a day and closes off a single car space. A door on a Derwent Park depot or a marine supplier near the wharves may cycle all shift, carry a wider and heavier curtain, and run on an industrial operator wired in by an electrician. Commercial installs also bring lifting gear on sloping sites, sealed motors for damp salty air, and work timed around trading hours, none of which a residential job needs.

Commercial garage door sizes and how size drives price

Opening size is the first thing that moves a Hobart quote. Motorised, a roller door near 3m x 3m costs $3,100–$5,350 installed, near 4m x 4m $4,475–$7,300, and near 5m x 5m $5,850–$9,700. A bigger curtain is heavier, so the drum, springs and operator all scale up with it. On hillside sites the measure should include the fall across the floor, because a sloping threshold needs a shaped bottom seal or packing before the door closes cleanly.

What Actually Moves the Commercial Garage Door Cost in Hobart

How to Keep the Commercial Garage Door Cost Sane in Hobart

1
Keep the existing opening size where possible; widening a lintel in an old masonry wall can cost more than the new door.
2
Fit a pedestrian door beside a big shutter so staff stop running the main curtain for every trip in winter.
3
Have each door serviced at $145–$340 a year, and hose salt off the guides between visits on waterfront sites.
4
Replace a tired operator at $730–$2,425 per door instead of the whole door when the curtain and drum are still sound.
5
Choose a curtain colour from the installer's stock range rather than a custom finish, which adds cost and lead time.

Commercial garage door cost by door type

Quick answerHobart prices: $2,750–$11,650 installed for an industrial roller shutter, $3,350–$19,200 ex GST for a sectional overhead door, and $10,650–$24,250 ex GST for a rapid-roll door supplied and fitted.

Most Hobart buyers pick between a shutter and a sectional. A shutter secures a shed, depot or boat store for the least outlay and copes with knocks. A sectional, especially the insulated version, suits a heated workshop or showroom where draughts and condensation are the complaint. Rapid-roll doors are a narrower choice, mainly for food and seafood businesses moving pallets through chilled rooms. Whichever type is chosen, the operator, controls and any pedestrian door are priced as extras, so compare quotes line by line.

Our Methodology

Commercial pricing on this page is compiled from Australian commercial and industrial garage-door suppliers and installers, published supplier price guides and product ranges as of November 2026. We cross-reference ranges from multiple sources; no contractor can influence a published figure. All prices are estimates, GST-inclusive unless a row says ex GST, and will vary with your specific opening, door spec and site. Always get multiple written quotes. Last reviewed November 2026. Read our full methodology →

Commercial garage door prices, product by product

Industrial roller shutters run $2,750–$11,650 installed in Hobart, typically $4,400. Width drives the price first, then curtain gauge, wind locks and a single-phase or three-phase drive. A machinery shed at Brighton or a depot in Glenorchy usually lands mid-band; a broad truck entry with a heavy curtain and industrial operator sits near the upper figure.

Sectional overhead doors cost $3,350–$19,200 installed ex GST, typically $9,400. The insulated version is $285–$390 per m² of door, supply only and ex GST, so a door about 4m wide and 3m high comes to $3,420–$4,680 supplied, with installation quoted on top. Glazed panels and a pass door add to either version.

High-speed rapid-roll doors are $10,650–$24,250 supplied and installed ex GST, typically $14,550. The case for one rests on traffic: a chilled room crossed by forklifts dozens of times an hour loses less cold through a door that opens and shuts in seconds. Internal doors avoid the extra cost of standing up to wind and rain.

A replacement operator costs $730–$2,425 per door, with heavy shutters and wide sectionals using three-phase units toward the upper end. Annual servicing is $145–$340 a year per door and should include lubrication, spring tension, guide alignment and a reversing test. On waterfront sites, ask for corrosion checks on fixings and the bottom rail as well.

Commercial garage doors — go deeper

Which door for which job?

Boat stores, machinery sheds and depots in Brighton, Moonah and Cambridge: a roller shutter, or a motorised roller door on smaller openings, gives security for the least spend and needs no insulation if the space is never heated.

Heated workshops, offices and showrooms: an insulated sectional keeps warmth in through Hobart's long cool season and stops condensation dripping inside the door.

Food, seafood and cold storage operations: a rapid-roll door on the internal opening between chilled rooms and dispatch, with a shutter on the outside wall for security after hours. In the heritage-listed sandstone warehouses around Salamanca, get heritage advice before any door change, then size the door to the existing arch or lintel.

Red flags when comparing commercial door installers

Roller door sizes and prices in Hobart

Where a Hobart roller door goes into an existing opening, such as an older brick shed in Moonah or a unit at Cambridge, the size of that opening sets the row. A 3m x 3m opening takes a manual door at $1,950–$3,500 installed, typically $2,575, or a motorised one at $3,100–$5,350 installed. Near 4m x 4m the motorised price is $4,475–$7,300 installed, and near 5m x 5m it is $5,850–$9,700 installed.

Running costs are per door and worth adding to the first quote. Servicing comes to $145–$340 a year for each door, so a depot with three bays would set aside $435–$1,020 a year, and replacing an operator is $730–$2,425 per door. Doors close to the Derwent are worth servicing on schedule, because salt air works on springs and guides.

Truck bays and wide machinery openings in Derwent Park or Glenorchy often move to the industrial roller shutter, $2,750–$11,650 installed. Where a heated workshop sits behind the door, an insulated sectional is worth pricing too: its panels cost $285–$390 per square metre ex GST as a supply-only line, and the fitting is quoted separately.

Commercial roller door cost in Hobart for sheds, workshops and depots

Roller doors in Hobart for commercial sites cost $1,950–$3,500 installed for a manual door around 3m x 3m, typically $2,575. Adding a motor to that size takes it to $3,100–$5,350 installed. A motorised 4m x 4m roller door costs $4,475–$7,300 installed, and a 5m x 5m motorised door $5,850–$9,700 installed, with typical jobs near $7,100.

Most commercial roller door work in Hobart is on sheds and workshops in Glenorchy, Moonah, Derwent Park, Cambridge and Kingston, plus marine and seafood businesses along the Derwent. Cold, damp winters make manual doors heavy and stiff, so many owners motorise. Where a shed is heated, or used for storage that must stay cool, insulated sectional panels at $285–$390 per square metre of door, supply only ex GST, are an alternative to a roller door. Wider truck openings move into industrial roller shutters at $2,750–$11,650 installed.

Replacing a worn motor costs $730–$2,425 per door and an annual service is $145–$340 a year per door, covering spring tension, guides and safety reversing. A Hobart roller door quote should state the opening size, the curtain material and colour, whether it is manual or motorised, the weather seals fitted, the motor and remotes, and whether removal of the old door and making good the opening are included.

What a Compliant Commercial Garage Door Quote Includes — Cost in Hobart

Hobart commercial garage door quotes need to cover freight, lead time and cold-weather detail as well as the door itself. Ask each installer to state the price basis of every line, since the table above mixes installed figures with ex GST supply figures.

Frequently Asked Questions — Commercial Garage Door Cost in Hobart

What does replacing an old commercial door cost in Hobart?
Replacing an old commercial door in Hobart costs $2,750–$11,650 installed for an industrial roller shutter, or $3,350–$19,200 installed, ex GST, for a sectional overhead door. The quote should include removing and disposing of the old curtain or panels, checking the frame and fixings, and any new motor. Older sheds in Glenorchy, Moonah and Derwent Park may need packing or new steel where the opening is out of square.
How much is a commercial roller door in Hobart?
Our Hobart table puts a manual roller door about 3 m x 3 m at $1,950–$3,500 installed, a motorised one about 3 m x 3 m at $3,100–$5,350 installed and a motorised one about 4 m x 4 m at $4,475–$7,300 installed.
How much does a roller door cost by size in Hobart?
In our Hobart table: a motorised roller door about 3 m x 3 m $3,100–$5,350 installed, about 4 m x 4 m $4,475–$7,300 installed and about 5 m x 5 m $5,850–$9,700 installed.
What does an industrial door motor replacement cost in Hobart?
A replacement motor or operator for an industrial door in Hobart costs $730–$2,425 per door, typically $1,225 per door. Heavy roller shutters and wide sectionals often use three-phase operators near the top of that band, while small roller doors use lighter units. Marine and seafood sites along the Derwent should ask for a sealed operator and corrosion-resistant fittings.
How much does a high-speed door cost for a Hobart food or seafood plant?
In Hobart, a rapid-roll door costs $10,650–$24,250 supply and install, ex GST, typically $14,550 supply and install. Seafood, food processing and cold storage sites around the Derwent use them on internal openings where forklifts pass constantly and a slow door would let chilled air escape. Opening size, curtain type, activation sensors and whether the door faces the weather set the price.
What do insulated commercial doors cost in Hobart?
Hobart businesses pay $285–$390 per square metre of door for insulated PU-core panels, supplied without fitting and ex GST, typically $335 per square metre. Built into a sectional overhead door, the installed price is $3,350–$19,200 ex GST. Through cold, damp Hobart winters an insulated door helps heated workshops, showrooms and offices hold warmth and keeps condensation off the inside of the door.
What does yearly servicing of a commercial door cost in Hobart?
A yearly commercial door service in Hobart is $145–$340 per door, and $245 is the common charge. Cold, damp winters are the issue here: condensation rusts springs and bearings, old grease stiffens on frosty mornings, and motors labour against sticky guides. The visit should re-grease and re-tension, test limits and safety reversing, and check wind locks on exposed doors along the Derwent. Workshops in Glenorchy, Moonah and Kingston and shop doors in Sandy Bay all benefit from a service booked ahead of winter.
What takes a Hobart sectional door quote toward the upper end?
A commercial sectional overhead door in Hobart spans $3,350–$19,200 installed, ex GST, with $9,400 typical, and the spread is mostly about specification. A single plain panel door on a Moonah workshop sits low. Width and height, insulated panels for a heated showroom, glazed sections, a pass door, a heavier-duty operator for constant use and wind locks all add lines, and a Battery Point or Sandy Bay streetscape may call for a colour or finish beyond the stock range. Headroom work to fit the tracks is another cost to confirm.
How much is a small manual roller door for a Hobart shop storeroom?
A manual roller door around 3m by 3m for a Hobart storeroom or shop rear access is $1,950–$3,500 installed, typically $2,575. For a New Town or Bellerive shop that opens the door a few times a day for deliveries, the manual curtain keeps the price down and has nothing electrical to fail in a cold snap. If staff will lift it dozens of times daily, the motorised version of the same size at $3,100–$5,350 installed saves backs and time, and an operator can be added later if the opening is wired.

Advertise with us

Reach Australian businesses researching commercial service costs. Fill in your details and we'll be in touch within 1 business day.

Thanks! We'll be in touch

Expect a reply within 1 business day.

Got a question about costs?
Chat with Sam
Sam the Platypus
Online now
Powered by What's The Damage