Independent Australian Cost Guides
Updated November 2026

How Much Does Gyprock Cost?

gyprock cost Australia - plastering cost

Gyprock costs $25–$65 per square metre installed in 2026, with most jobs quoted around $41/m² for fixing, setting and finishing — the board itself is usually supplied on top. In whole-job terms: re-sheeting a room's walls runs $600–$2,500, replacing a ceiling $800–$3,000, and gyprocking an entire 3-bed house typically lands at $12,300–$16,000 at standard rates. And if you're wondering about the name — Gyprock is a brand of plasterboard used so universally here that Australians use the two words interchangeably; every price on this page covers both.

Gyprock cost per square metre

Per-square-metre rates are how plasterers price boarding work. The rates below cover the labour — fixing the sheets, setting the joints and finishing ready for paint. Check whether board supply is itemised on your quote; per the going market it usually sits outside these figures.

JobLowTypicalHighUnit
Plasterboard / Gyprock installation$25$41$65/m²
Acoustic / soundproof plasterboard$35$55$85/m²
New stud wall (supply + install)$60$95$150/m²
Skim coat over existing walls$15$28$50/m²
Cornice installation$10$15$50/lm
Plasterer hourly rate$50$77$120/hr

Cost to gyprock a room

Re-sheeting the walls of a single room costs $600–$2,500, with most standard bedrooms landing near $1,200 — that covers strip-out of the old lining where needed, new board, setting and a paint-ready finish. Add the ceiling and the room runs roughly $1,400–$5,500 all up. What pushes a room to the top of the band: full strip-out of old hard plaster, new cornice at $10–$50 per lineal metre, and premium finish levels.

Gyprock ceiling replacement cost

Replacing a gyprock ceiling costs $800–$3,000 per room, covering removal of the old material, new plasterboard, and finishing. Ceilings consistently price 20–30% above the same area of wall work — the board is heavier, it needs temporary propping while it's fixed, and overhead finishing is slower to get right. Water-stained or sagging ceilings are the classic trigger; where the damage is localised, a water damage repair at $300–$1,500 can beat full replacement.

Cost to gyprock a whole house

Whole-house quotes come from measured board area, so here's the method plus the bands it produces. Ceilings roughly equal the floor area, and at standard 2.4m ceilings the walls carry about twice that again — so total board area lands near three times the floor plan. Applied to the $25–$65/m² installed rate:

Home sizeFloor areaBoard area (walls + ceilings)Installed at typical $41/m²Full range
2-bed unit60–90m²~180–270m²$7,400–$11,100$4,500–$17,600
3-bed house100–130m²~300–390m²$12,300–$16,000$7,500–$25,400
4-bed house140–180m²~420–540m²$17,200–$22,100$10,500–$35,100

So the cost of gyprocking a 3-bedroom house typically lands at $12,300–$16,000 for installation and finishing, with board supply on top — budget-rate jobs on smaller plans start near $7,500, and large or premium-finish homes run past $25,000. Two-storey access, full strip-out of old lining and acoustic board in bedrooms all push a house toward the upper band.

What's included in a gyprock installation quote

gyprock installation cost - plastering cost

A standard installed rate covers three stages: fixing (screwing the sheets to studs or battens), setting (taping and cementing the joints and screw heads), and finishing (sanding to a paint-ready surface). Quotes usually assume a standard finish level — a premium level 5 finish for critical light or gloss paint prices above the standard band, so get it itemised if that's the spec. The board itself, cornice, and disposal of old material are the line items that most often sit outside the headline rate; a quote that itemises all four is the easiest to compare.

Repairs vs re-sheeting

Not every damaged wall needs new board. Patching a small hole runs $150–$280 per job, crack repair $80–$300 per crack, and water damage repair $300–$1,500 depending on spread — large water jobs may also need mould remediation before the plasterer starts. Re-sheeting earns its keep when the old lining is drummy, crumbling or patched so many times the joins telegraph through paint; at that point the $600–$2,500 room rate resets the surface entirely. Plastering prices moved about 4% over the past year — every figure on this page was re-verified in November 2026 against 90+ sources.

Step 1 of 2

What do you need a callback about?

One tap — we'll show you the going rate, then take your number.

You're in.

A local installer will be in touch about your job. No spam, no call centre.

Gyprock cost calculator: price your job from the per-square-metre rate

There is no flat price for a gyprock job, so the quickest estimate is the one installers use themselves: board area multiplied by the installed rate. Measure each wall (length by height) and each ceiling (length by width), add them up, and set that area against the installed rate of $25–$65 per m², typically $41. The room, ceiling and whole-house rows on this page are what that arithmetic gives at typical sizes: a 2-bed unit with roughly 180–270 m² of board lands at $7,400–$11,100 at the typical rate (full range $4,500–$17,600), a 3-bed house at $12,300–$16,000 (full range $7,500–$25,400) and a 4-bed house at $17,200–$22,100 (full range $10,500–$35,100).

Add the lines a per-metre rate does not carry. Cornice is priced by the lineal metre at $10–$50, a skim coat over sound existing walls is $15–$50 per m² instead of new board, acoustic board for a shared wall is $35–$85 per m², and a short list of patches is usually quoted at the plasterer's hourly rate of $50–$120. What no calculator sees is access, a level 5 finish for gloss paint or critical light, and removing and disposing of the old lining, so use the estimate to check quotes rather than replace them. Get quotes from local plasterers through the form on this page.

Gyprock price per m2: what moves the cost inside the $25–$65 band

Standard 10 mm board on open, straight walls sits at the low end of the $25–$65 per m² band. Ceilings, 13 mm board, wet-area board and rooms full of windows, bulkheads and corners push the rate toward the middle, because the setting and sanding take longer per sheet. Acoustic board is its own row at $35–$85 per m², and a new stud wall at $60–$150 per m² is framing plus board on both faces, so compare quotes row by row rather than on a single per-metre number.

Small jobs rarely get a per-metre price at all: a plasterer will quote the day or the hour at $50–$120, which is why a single room can cost more per square metre than a whole house. When the existing walls are sound, ask whether a skim coat at $15–$50 per m² will do before paying for new sheets.

Plastering in your city

Verified November 2026 ranges — tap your city for the full local guide.

Sydney$57–$138/hr Melbourne$53–$126/hr Brisbane$50–$120/hr Perth$53–$126/hr Adelaide$46–$110/hr Gold Coast$49–$118/hr Canberra$55–$132/hr Hobart$45–$108/hr Darwin$50–$120/hr Newcastle$48–$114/hr Geelong$47–$112/hr Sunshine Coast$49–$116/hr Townsville$54–$130/hr Wollongong$54–$130/hr Byron Bay$53–$126/hr

Frequently asked questions

How much does gyprock cost per square metre?

Gyprock installation costs $25–$65 per square metre in 2026, with most jobs landing around $41/m². That rate covers fixing, setting and finishing the board — the plasterboard itself is usually supplied separately. Acoustic or soundproof board runs $35–$85/m² installed.

How much does it cost to gyprock a room?

Re-sheeting the walls of a single room costs $600–$2,500, with a typical room landing near $1,200. Adding the ceiling takes the room to roughly $1,400–$5,500 all up, since ceiling replacement runs $800–$3,000 on its own.

How much does it cost to replace a gyprock ceiling?

Replacing a gyprock ceiling costs $800–$3,000 per room, including removing the old material, installing new plasterboard and finishing. Ceilings price 20–30% above equivalent wall work — the board is heavier, needs temporary support and is harder to finish without marks.

How much does it cost to gyprock a 3-bedroom house?

A 3-bedroom house (100–130m² of floor) carries roughly 300–390m² of board once ceilings and both wall faces are counted. At typical 2026 rates that is $12,300–$16,000 installed for the labour and finishing, with the full spread running $7,500–$25,400 — board supply usually comes on top.

Is Gyprock the same as plasterboard?

Yes. Gyprock is a brand of plasterboard — also called drywall — that is used so widely in Australia the name has become generic. Plasterers quote gyprock and plasterboard work interchangeably, and the prices on this page apply to both.

Do plasterers charge per square metre or per hour?

Boarding and sheeting work is normally quoted per square metre at $25–$65/m², while repairs, patching and finishing are often charged hourly at $50–$120 (typically $77/hr). For bigger jobs some plasterers quote a day rate of $350–$850 instead.

← Back to plastering cost guide

Advertise with us

Reach thousands of Australian homeowners researching trade costs. Fill in your details and we'll be in touch within 1 business day.

Thanks! We'll be in touch

Expect a reply within 1 business day.

Got a question about costs?
Chat with Sam
Sam the Platypus
Online now
Powered by What's The Damage
Planning gyprock work?Get free quotes from local pros →