Updated November 2026·Independently researched·11 min read
Commercial signage in Wollongong runs $1,800–$5,000
for an illuminated lightbox fascia sign installed, GST included - letters, pylons, graphics and wraps below
A Wollongong shopfront lightbox, illuminated and installed, costs $1,800–$5,000, typically $3,000. An Unanderra fabricator after a single-tenant pylon on its frontage is pricing $8,000–$30,000, and a Thirroul cafe that only wants an A-frame for the footpath spends $120–$600.
+4.4%Commercial Signage costs in Wollongong are up around 4.4% over the past year, re-verified against 90+ sources in November 2026.Year on year
Typical illuminated lightbox fascia in Wollongong
$3,000
per sign installed, Wollongong 2026, GST included
Illuminated lightbox fascia sign, installed
$1,800-$5,000
Illuminated 3D letter set, installed (5-8 letters)
$3,000-$10,000
Single-tenant pylon sign, 4-6 m, installed
$8,000-$30,000
$1,800$3,000$5,000
In Wollongong, the sign itself sets the starting point. An illuminated lightbox fascia installed is $1,800–$5,000; a set of illuminated 3D letters is $3,000–$10,000; a single-tenant pylon of 4 to 6 metres is $8,000–$30,000, and a multi-tenant pylon of 8 metres and up is $15,000–$50,000. On the glazing, frosted film runs $40–$180 a square metre and printed graphics $80–$250 a square metre.
Where the sign goes is what spreads two Wollongong quotes for the same fascia. Steelworks grit around Port Kembla and salt off the escarpment coast both shorten the life of a sign face, so cleaning and marine-grade materials belong in the quote; a tenancy in Wollongong Central or Stockland Shellharbour meets the centre's guidelines on top of the council's; and a Crown Street Mall frontage usually means after-hours work and a boom lift. Anything illuminated also needs an electrical connection by a licensed electrician, $200–$2,400, kept as its own line.
The smaller lines are worth reading too: design and artwork setup at $150–$960 when the logo is only a JPEG, old sign removal and make-good at $200–$800 when a Keira Street tenancy turns over, and a full van wrap at $3,500–$8,500 for a fleet that runs the length of the Illawarra. Prices include GST.
Quick answerCommercial signage in Wollongong runs $1,800–$5,000 for an illuminated lightbox fascia sign installed in 2026, $3,000–$10,000 for a set of illuminated 3D letters and $8,000–$30,000 for a single-tenant pylon, with the fascia size, illumination and council approvals setting the total. All figures on this page include GST. Get free Wollongong quotes →
Commercial Signage Prices in Wollongong 2026: Cost Table and Price List
Service
Low
Typical
High
Illuminated lightbox fascia sign, installed
$1,800per sign
$3,000
$5,000
Illuminated 3D letter set, installed (5-8 letters)
$3,000per set
$5,500
$10,000
Face-lit LED 3D letter, 300-500 mm (letters only)
$150per letter
$400
$700
Single-tenant pylon sign, 4-6 m, installed
$8,000per sign
$18,000
$30,000
Multi-tenant pylon sign, 8 m and up, installed
$15,000per sign
$30,000
$50,000
Monument or entry sign, installed
$2,500per sign
$6,000
$18,000
Printed A-frame sign
$120per sign
$300
$600
Frosted or privacy window film, installed
$40/m²
$100
$180
Printed window or wall graphics, installed
$80/m²
$150
$250
Full vehicle wrap, car or sedan
$2,500per vehicle
$3,500
$4,500
Full vehicle wrap, van
$3,500per vehicle
$5,500
$8,500
Statutory safety sign, supply only
$7.50each
$40
$165
Wayfinding sign suite, per office floor
$2,000per floor
$3,500
$6,000
Electrical connection for an illuminated sign
$200per sign
$600
$2,400
Design and artwork setup
$150per job
$400
$960
Old sign removal and make-good
$200per job
$450
$800
Scoping commercial signage work in Wollongong? Get a quote from a local commercial contractor - free, no obligation.
Prices include GST. Wollongong and the Illawarra, November 2026.
What does an illuminated shopfront sign cost in Wollongong?$1,800–$5,000 installed for a lightbox fascia, $3,000 typical. A set of illuminated 3D letters costs $3,000–$10,000, and the electrical connection by a licensed electrician is a separate $200–$2,400 line.
What gets added to a Wollongong signage quote?Design and artwork setup at $150–$960 when there are no vector files, old sign removal and make-good at $200–$800 when taking over a tenancy, the electrical connection at $200–$2,400 for anything illuminated, and the council's own permit fee where a sign needs approval.
Worked Commercial Signage Cost Scenarios — Wollongong
Three Wollongong jobs priced against this page's rows: a cafe on Keira Street, an office floor in the CBD and a workshop at Unanderra. Each line names the row it comes from; the quote you receive prices your own frontage and approvals.
Keira Street cafe. Opening in a former Keira Street shop, a cafe has the old fascia taken down and the wall made good at $200–$800, mounts an illuminated lightbox fascia at $1,800–$5,000 ($3,000 typical) with its electrical connection at $200–$2,400 listed separately, applies frosted film to the lower glass at $40–$180 a square metre and sets a printed A-frame on the footpath at $120–$600.
CBD office floor. Fitting out a floor a block from the Crown Street Mall, a firm orders a wayfinding sign suite at $2,000–$6,000, supply-only statutory safety signs at $7.50–$165 each for the fire stairs and plant rooms, and illuminated 3D letters in the lobby at $3,000–$10,000, paying $150–$960 for design and artwork setup because its logo files are not vector.
Unanderra workshop. An engineering workshop at Unanderra puts a single-tenant pylon of 4 to 6 metres at its entry for $8,000–$30,000, typically $18,000, asks for the engineering certificate, the council application and a cleaning schedule for the grit to be named on the quote, and wraps its service vans at $3,500–$8,500 each.
You're in.
A local installer will be in touch about your job. No spam, no middleman.
Scoping commercial signage work in Wollongong? Get a quote from a local commercial contractor - free, no obligation.
Prices include GST. Wollongong and the Illawarra, November 2026.
Commercial Signage Costs by Sector in Wollongong
Wollongong's signage work runs from the CBD, the Crown Street Mall and the harbour, along Crown Street, Keira Street, the Princes Highway at Fairy Meadow and Addison Street in Shellharbour, into Wollongong Central, Stockland Shellharbour and Figtree Grove, and out to the industrial land at Unanderra, Port Kembla, Kembla Grange and Albion Park Rail, with venues at North Wollongong, the harbour and Thirroul.
Retail strips: Crown Street, Keira Street, Fairy Meadow, Shellharbour - Strip shops mostly order an illuminated lightbox fascia at $1,800–$5,000 or illuminated 3D letters at $3,000–$10,000, with frosted film at $40–$180 a square metre and a printed A-frame at $120–$600; frontages close to the beach at North Wollongong and Thirroul are worth quoting with marine-grade fixings.
Shopping centres: Wollongong Central, Stockland Shellharbour, Figtree Grove - A centre tenancy usually carries illuminated 3D letters on the bulkhead, $3,000–$10,000 installed or $150–$700 a letter for the letters alone, and the centre's guidelines sit on top of the council's approval.
Industrial: Unanderra, Port Kembla, Kembla Grange, Albion Park Rail - A single-tenant pylon at $8,000–$30,000 on the street, a multi-tenant pylon at $15,000–$50,000 at an estate entry and a monument or entry sign at $2,500–$18,000 at the gate, each with engineering certification on the quote; near the steelworks, cleaning belongs on it too.
Offices: CBD, Warrawong, Shellharbour - Office fit-outs take a wayfinding sign suite at $2,000–$6,000 a floor, supply-only statutory safety signs at $7.50–$165 each, and printed window or wall graphics at $80–$250 a square metre in reception.
Fleets and hospitality: Unanderra, Albion Park Rail, North Wollongong, Thirroul - Trade and delivery fleets based at Unanderra and Albion Park Rail wrap vans at $3,500–$8,500 and cars or sedans at $2,500–$4,500; venues at North Wollongong, the harbour and Thirroul add menu and price displays, which the ACCC says must show one total price including GST to consumers.
What a Compliant Commercial Signage Quote Includes — Cost in Wollongong
Before comparing Wollongong quotes, check each one prices the same sign size, substrate and illumination, says whether install, electrical connection and council approval are in or out, and shows design, removal and GST on their own lines.
Sign type, dimensions, substrate and finish - lightbox, fabricated letters, pylon, film or print - with illumination stated as face-lit, halo or unlit
Install as its own line, naming access equipment such as a boom lift or scaffold and any after-hours or traffic-management requirement
Electrical connection for an illuminated sign at $200–$2,400, done by a licensed electrician, with the certificate named
Design and artwork setup at $150–$960 where no print-ready vector files are supplied, or a nil line where they are
Old sign removal and make-good at $200–$800 when the frontage carries a previous tenant's sign
Sign-permit or planning application fees shown as a pass-through at the council's published rate, and who lodges it
Engineering certification for a pylon, monument or projecting sign, and the wind rating it is built to
Warranty terms on LEDs, laminates and print fade, and the service call-out basis after the warranty
A single GST basis across every line, with the sign company's ABN and proof of insurance
Commercial signage cost in Wollongong: Crown Street, the centres and the Port Kembla estates
A Wollongong shopfront's commercial signage cost begins with the fascia, $1,800–$5,000 installed for an illuminated lightbox (most come in near $3,000) or $3,000–$10,000 for a set of illuminated 3D letters. Pylons run $8,000–$30,000 for a single tenant and $15,000–$50,000 for a multi-tenant sign at a Kembla Grange or Albion Park Rail estate entry; a monument or entry sign at the gate is $2,500–$18,000, and a 300 to 500 mm face-lit LED letter on its own is $150–$700 before install.
The rest of a Wollongong quote comes from the site. At Port Kembla and Unanderra steelworks grit shortens the life of a sign face, so cleaning should be on the quote; near the beach at North Wollongong and Thirroul, salt calls for marine-grade frames; a Wollongong Central or Stockland Shellharbour tenancy adds an approval step and often a set letter style; a Crown Street Mall frontage adds after-hours work and a boom lift. Around all of it sit the electrical connection at $200–$2,400, design and artwork setup at $150–$960 where there are no vector files, and old sign removal and make-good at $200–$800 on a changeover.
The NSW Planning Portal says a business identification sign can be exempt development when it is securely fixed, has the owner's written consent and stays within the cap of three signs on a single-tenant building or six per building, that a sign over a road needs approval under section 138 of the Roads Act, and that projecting wall, pylon and directory signs in business and industrial zones are complying development under the Commercial and Industrial Alterations Code. Its fact sheet adds that an illuminated exempt sign must conceal its cables, must not animate or flash, and within 50 metres of a residential zone may only be lit between 7 am and 10 pm. Where a Wollongong sign needs approval, the quote should name the party lodging with the council and pass the council's published fee through as its own line.
Commercial signage cost by sign type and size in Wollongong
Quick answerSign type sets the Wollongong bracket: a Keira Street or Thirroul cafe sits at $120–$600 for an A-frame and $1,800–$5,000 for a lightbox, a Wollongong Central or Figtree Grove tenancy at $3,000–$10,000 for illuminated 3D letters, and an Unanderra or Kembla Grange frontage at $8,000–$30,000 to $15,000–$50,000 for a pylon.
There are two ways size shows up in a Wollongong sign price. Fascias and lightboxes are priced by width and lighting, so a long illuminated frontage on Crown Street climbs toward the top of $1,800–$5,000; fabricated letters are priced each, $150–$700 for a 300 to 500 mm face-lit letter, which is why a long trading name on a Wollongong Central bulkhead moves up through the $3,000–$10,000 set band. Film and print are priced by area, $40–$180 a square metre frosted and $80–$250 printed, so a long glazed frontage near the harbour is simply more metres.
The second is height. A single-tenant pylon of 4 to 6 metres at $8,000–$30,000 needs a footing, engineering and a crane day; a multi-tenant pylon of 8 metres and up at $15,000–$50,000 at an Albion Park Rail estate entry needs all three on a larger scale and a council application besides. Vehicles scale in the same way, a car or sedan wrap at $2,500–$4,500 set against a full van wrap at $3,500–$8,500 for a long-wheelbase van based at Unanderra.
Frequently Asked Questions — Commercial Signage Cost in Wollongong
What is the price of commercial signage in Wollongong?
From our Wollongong table: $1,800–$5,000 for an illuminated lightbox fascia sign installed (typically $3,000); $3,000–$10,000 for an illuminated 3D letter set (typically $5,500); $8,000–$30,000 for a single-tenant pylon sign (typically $18,000).
How much does an illuminated shopfront sign cost in Wollongong?
An illuminated lightbox fascia sign in Wollongong costs $1,800–$5,000 installed, with $3,000 typical, plus the electrical connection at $200–$2,400 by a licensed electrician. A Crown Street Mall frontage usually adds after-hours work and a boom lift to the install line, and near Port Kembla the quote should add a cleaning plan; a single-storey shop on the Princes Highway at Fairy Meadow usually needs neither.
What does a pylon sign cost in Wollongong?
Going by our Wollongong table, a single-tenant pylon sign of 4 to 6 metres costs $8,000–$30,000 installed, typically $18,000, and a multi-tenant pylon of 8 metres and up $15,000–$50,000. In Wollongong the buyers are mostly the estates at Unanderra, Port Kembla, Kembla Grange and Albion Park Rail; the quote should name the engineering certificate, the footing and who lodges the council application.
How much are illuminated 3D letters in Wollongong?
A set of 5 to 8 illuminated 3D letters installed costs $3,000–$10,000 on our Wollongong table, with $5,500 typical; priced per letter, a face-lit LED letter of 300 to 500 mm is $150–$700 for the letters alone, before install.
Do I need council approval for a sign in Wollongong?
The NSW Planning Portal says a business identification sign can be exempt development when it is securely fixed, has the owner's written consent and stays within the cap of three signs on a single-tenant building or six per building, that a sign over a road needs approval under section 138 of the Roads Act, and that projecting wall, pylon and directory signs in business and industrial zones are complying development under the Commercial and Industrial Alterations Code. Its fact sheet adds that an illuminated exempt sign must conceal its cables, must not animate or flash, and within 50 metres of a residential zone may only be lit between 7 am and 10 pm. The council's own fee schedule applies on top in Wollongong, and a tenancy at Wollongong Central or Stockland Shellharbour needs the centre's approval as well; ask the sign company to show the council fee as a pass-through line and name who lodges.
Who connects an illuminated sign in Wollongong?
Energy Safe Victoria says to always engage a registered electrical contractor, who sends a licensed electrician, that do-it-yourself electrical work is illegal and that a Certificate of Electrical Safety is issued for installation work; Building Commission NSW says a licence is required for any electrical wiring work regardless of value, with a Certificate of Compliance for Electrical Work lodged through its eCert portal. On our Wollongong table the electrical connection for an illuminated sign is $200–$2,400, with $600 typical, and the sign quote should show it as its own line.
What do window graphics and frosting cost in Wollongong?
Frosted or privacy window film costs $40–$180 a square metre installed in Wollongong, and printed window or wall graphics $80–$250 a square metre. Glazed frontages in the Wollongong CBD, at Warrawong and in Shellharbour are the usual jobs, and the quote should price film and print by the square metre with the measured area shown.
What does a vehicle wrap cost in Wollongong?
A full wrap on a car or sedan costs $2,500–$4,500 in Wollongong, with $3,500 typical, and a full van wrap $3,500–$8,500. Trade and delivery fleets based at Unanderra, Kembla Grange and Albion Park Rail are the usual Wollongong buyers; wraps are priced per vehicle, and the quote should name the film brand and the warranty and, near Port Kembla, say how that warranty treats grit and cleaning.
What signs does a Wollongong workplace have to have?
The National Construction Code 2022, Volume One Part E4, requires an exit sign on, above or beside every required exit, direction signs where an exit is not readily apparent, and exit signs that comply with AS/NZS 2293.1 or the Specification 25 photoluminescent alternative and are lit whenever the building is occupied. WorkSafe ACT classes workplace safety signs as prohibition, mandatory, danger, warning, emergency and fire signs, with colours and placement set by AS 1319-1994 Safety signs for the occupational environment, and the Safe Work Australia model code of practice for the work environment says exit locations should be easy to identify, with signs pointing to exit doors. Supply-only statutory safety signs cost $7.50–$165 each on our Wollongong table. A Wollongong office floor in the CBD often bundles those with a wayfinding sign suite at $2,000–$6,000; ask for the floor plan the signs were set out from.
Related Commercial Signage Cost Guides — Wollongong